The stress represented by sin (t) + 2 belongs to which category?

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

The stress represented by sin (t) + 4 belongs to which category?

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The stress represented by sin (t) + 1 belongs to which category?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The stress represented by cos (t) belongs to which category?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Fatigue failure is time dependent failure.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross-section and highest value of actual stress near discontinuity.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Is it logical to use fluid analogy to understand the phenomenon of stress concentration?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is?

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In which of the following case stress concentration factor is ignored?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Use of multiple notches in a V shaped flat plate will

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by

asked 1 day ago in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Determine the torsional shear stress in the welds if P=8kN and thickness of the welds is assumed t.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Two plates each of thickness t are to be riveted together. If length of shank portion necessary to form the closing head is a, then length of rivet shank is given by?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The pressure intensity at an element on long shoe brake varies directly with the sin of the pressure angle of the element of friction lining.

asked Jan 21 in Machine Design by Chris (52.6k points)

+1 vote

1 answer

Find the length of weld 2 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In distortion energy theorem, if a unit cube is subjected to biaxial stress, then S(yt) is given by which of the following?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Tolerance for a shaft of 50mm diameter as the basic size, with the fundamental deviation denoted by g and tolerance of grade 7 is represented as?

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by

asked 1 day ago in Machine Design by Carter (89.5k points)

...