Determine the torsional shear stress in the welds if P=8kN and thickness of the welds is assumed t.

Question

Determine the torsional shear stress in the welds if P=8kN and thickness of the welds is assumed t.

1 Answer

Related questions

0 votes

0 answers

Calculate the direct shear stress in the welds by ignoring torsional shear stress if P=8kN and thickness of weld is 5mm.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

While considering moment of inertia for calculating torsional shear stress, J=I(xx) + I(yy), which of the following can be neglected in context with the following figure?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate size of the welds if P=40kN, leg=4mm and e=400mm. Maximum permissible value of shear stress in the weld is 70N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the length of weld 1 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the total length of weld required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the length of weld 2 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which equations can be used to find the resisting force in the two welds?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate the bending stress in the welds if P=40kN, leg=4mm and e=400mm.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by crushing consideration if permissible compression stress in rivets is 120N/mm², thickness of plate 3mm and P=15kN.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by shear considerations if permissible shear stress in rivets is 60N/mm² and P=15kN.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate width of the band if permissible tensile stress is 80N/mm². Force P=15kN and diameter of the rivet can be taken as 9mm. Given thickness=3mm

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets if permissible shear stress is 60N/mm². Bolts are separated by 100mm and force P=30kN.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the primary shear stress on each rivet if P=30kN and diameter of rivets is 15mm.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If secondary shear stress acting on any bolts is given by Cxr₁ where r₁ is the distance of bolt from CG, then find the value of C. Bolts are equidistant with spacing of 100mm. Force P=30kN.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

For the following welded joint l₁y₁=l₂y₂.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The moment of forces about the CG is ?

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The following welded joint is an example of

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Two plates each of thickness t are to be riveted together. If length of shank portion necessary to form the closing head is a, then length of rivet shank is given by?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by

asked Feb 2 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-01-27T14:03:55+0000

The appropriate answer is (c) 543.13/t

Check out the details: M=8000×150,r(farthest point)=√25²+25²,J=2x[tlᵌ/12 + Ar₁²] ; τ=Mr/J.

Determine the torsional shear stress in the welds if P=8kN and thickness of the welds is assumed t.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories