Calculate the diameter of the rivets by shear considerations if permissible shear stress in rivets is 60N/mm² and P=15kN.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

Calculate the diameter of the rivets by crushing consideration if permissible compression stress in rivets is 120N/mm², thickness of plate 3mm and P=15kN.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate width of the band if permissible tensile stress is 80N/mm². Force P=15kN and diameter of the rivet can be taken as 9mm. Given thickness=3mm

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the diameter of the rivets if permissible shear stress is 60N/mm². Bolts are separated by 100mm and force P=30kN.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate size of the welds if P=40kN, leg=4mm and e=400mm. Maximum permissible value of shear stress in the weld is 70N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Calculate the primary shear stress on each rivet if P=30kN and diameter of rivets is 15mm.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Find the length of weld 1 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Find the total length of weld required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Find the length of weld 2 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate the bending stress in the welds if P=40kN, leg=4mm and e=400mm.

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Determine the torsional shear stress in the welds if P=8kN and thickness of the welds is assumed t.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If secondary shear stress acting on any bolts is given by Cxr₁ where r₁ is the distance of bolt from CG, then find the value of C. Bolts are equidistant with spacing of 100mm. Force P=30kN.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the shear stress in the pin.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Determine the diameter of the bolts used in rigid flange coupling if transmitted torque is 270N-m, pitch circle diameter=125mm and four bolts are emplace in the coupling. Permissible shear stress in the bolts is 70N/mm².

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Among flat head and snap head rivet, which has the higher head height?

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm².

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A strap is used in a lap joint which is riveted to each of the two plates.

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Lozenge joint is a kind of lap joint.

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Which of the following rivet head consist of frustum of cone attached to the shank?

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

What is the other name for pitch?

asked Jan 21 in Machine Design by Chris (48.2k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm²Find the maximum amount of shear stress to which the body is subjected.

asked 3 days ago in Machine Design by Carter (86.7k points)

...