Are the rivets subjected any bending moment in case of lap joint?

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

+1 vote

1 answer

A strap is used in a lap joint which is riveted to each of the two plates.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Lozenge joint is a kind of lap joint.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by crushing consideration if permissible compression stress in rivets is 120N/mm², thickness of plate 3mm and P=15kN.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by shear considerations if permissible shear stress in rivets is 60N/mm² and P=15kN.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are used in light sheet metal work?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Two plates each of thickness t are to be riveted together. If length of shank portion necessary to form the closing head is a, then length of rivet shank is given by?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Failure in rivet occurs by which mode?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate width of the band if permissible tensile stress is 80N/mm². Force P=15kN and diameter of the rivet can be taken as 9mm. Given thickness=3mm

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Among flat head and snap head rivet, which has the higher head height?

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following rivet head consist of frustum of cone attached to the shank?

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

What is the other name for pitch?

asked Jan 21 in Machine Design by Chris (52.6k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets if permissible shear stress is 60N/mm². Bolts are separated by 100mm and force P=30kN.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the effective force in vector form to which rivet 4 is subjected. Bolts are separated by 100mm and force P=30kN.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the effective force in vector form to which rivet 2 is subjected. Bolts are separated by 100mm and force P=30kN.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the tensile strength of rivets along B-B.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the tensile strength of rivets along C-C.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the pitch of the rivets.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the primary shear stress on each rivet if P=30kN and diameter of rivets is 15mm.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate the bending stress in the welds if P=40kN, leg=4mm and e=400mm.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the bending stress induced in the strip of the helical spring. The spring is subjected to a moment of 1250N-mm with breadth and thickens of the strip being 11mm and 1.5mmm respectively.

asked Jan 27 in Machine Design by Carter (89.5k points)

...