If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

Question

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

1 Answer

Related questions

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering combined effect of direct stress and bending stress.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the diameter of pin from shear consideration with maximum shear stress allowed is 40NN/mm² and an axial tensile force of 50kN is acting on the rod.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If for a curved beam of trapezoidal cross section, radius of neutral axis is 89.1816mm and radius of centroidal axis is 100mm, then find the bending stress at inner fibre whose radius is 50mm. Area of cross section of beam is 7200mm² and the beam is loaded with 100kN of load.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm²Find the maximum amount of shear stress to which the body is subjected.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 10N/mm². Find the inclination of the plane in which shear stress is maximal.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm². Find the minimum normal stress.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the shear stress in the pin.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the length of the pin.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If allowable shear stress in the shaft is 70N/mm² and torsional and bending moments are M=1185000N-mm and m=330000N-mm, find the diameter of the shaft.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the bending stress induced in the strip of the helical spring. The spring is subjected to a moment of 1250N-mm with breadth and thickens of the strip being 11mm and 1.5mmm respectively.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A maximum of how many roads may be connected using a knuckle joint?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are important parts of knuckle joint?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Knuckle Joint can’t be used to connect two intersecting rods.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In cold riveting like hot riveting shank is subjected to majorly tensile stress.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If no re boring allowance is to be given, then thickness of cylinder wall is max pressure is 3.5N/mm², bore diameter=200mm and permissible tensile stress is 40N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm². The diameter of shaft and width of key can be taken as 40mm and 10mm respectively.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. If modulus of elasticity is 207000N/mm², calculate the initial nip.

asked Jan 23 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-02-02T14:25:32+0000

Suitable answer is (a) 25.5mm

For a clear picture: σ= [P/A] + [My/I], where y=t & I=t(2t)ᴲ/12.

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories