In cold riveting like hot riveting shank is subjected to majorly tensile stress.

Question

In cold riveting like hot riveting shank is subjected to majorly tensile stress.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Cold riveting holds the connected parts better than hot riveting.

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In hot riveting the shank portion is subjected to compressive stress.

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Can the cotter joint be used to connect slide spindle and fork of valve mechanism?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The principle of wedge action is used in cotter joint.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

For components made of ductile materials like steel, subjected to static loading which of the following strength is used as a failure of criterion?

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm²Find the maximum amount of shear stress to which the body is subjected.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm². Find the minimum normal stress.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Calculate the diameter of pin from shear consideration with maximum shear stress allowed is 40NN/mm² and an axial tensile force of 50kN is acting on the rod.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A beam subjected to bending moment undergoes which of the following stresses?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

The total strain energy for a unit cube subjected to three principal stresses is given by?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

According to principal stress theory, which option represents the correct relation between yield strength in shear (YSS) and the yield strength in tension (YST)?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the shear stress in the pin.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The normal stress is perpendicular to the area under considerations, while the shear stress acts over the area.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is?

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If for a curved beam of trapezoidal cross section, radius of neutral axis is 89.1816mm and radius of centroidal axis is 100mm, then find the bending stress at inner fibre whose radius is 50mm. Area of cross section of beam is 7200mm² and the beam is loaded with 100kN of load.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Maximum Principal Stress Theory is not good for brittle materials.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Stress intensity factor is the critical value of stress at which crack extension occurs.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

For cast iron components, which of the following strength are considered to be the failure criterion?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Longer arm is of length 500mm. Calculate the reaction or force acting on the fulcrum.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Knuckle Joint can’t be used to connect two intersecting rods.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If there are residual stresses in the material, than lower factor of safety is used.

asked Jan 23 in Machine Design by Carter (86.7k points)

Chris · Answer 1 · 2026-01-27T10:26:36+0000

Correct answer is (b) False

For explanation: In cold riveting there is no reduction in length and hence no tensile stress. Shear stress dominates.

In cold riveting like hot riveting shank is subjected to majorly tensile stress.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories