If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is?

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

+1 vote

1 answer

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

In which of the following case stress concentration factor is ignored?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Use of multiple notches in a V shaped flat plate will

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The stress represented by sin (t) + 4 belongs to which category?

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The stress represented by cos (t) belongs to which category?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The stress represented by sin (t) + 1 belongs to which category?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

In distortion energy theorem, if a unit cube is subjected to biaxial stress, then S(yt) is given by which of the following?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If no re boring allowance is to be given, then thickness of cylinder wall is max pressure is 3.5N/mm², bore diameter=200mm and permissible tensile stress is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In cold riveting like hot riveting shank is subjected to majorly tensile stress.

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Calculate the diameter of pin from shear consideration with maximum shear stress allowed is 40NN/mm² and an axial tensile force of 50kN is acting on the rod.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate width of the band if permissible tensile stress is 80N/mm². Force P=15kN and diameter of the rivet can be taken as 9mm. Given thickness=3mm

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm²Find the maximum amount of shear stress to which the body is subjected.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm². Find the minimum normal stress.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm².

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If secondary shear stress acting on any bolts is given by Cxr₁ where r₁ is the distance of bolt from CG, then find the value of C. Bolts are equidistant with spacing of 100mm. Force P=30kN.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If distance between the bolts from the axis of tilting is 125mm and 25mm, then find the effective tensile force acting on the bolts lying at 125mm from tilting axis.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m.

asked Jan 21 in Machine Design by Chris (48.2k points)

...