The stress represented by cos (t) belongs to which category?

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

The stress represented by sin (t) + 4 belongs to which category?

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The stress represented by sin (t) + 1 belongs to which category?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is?

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

In which of the following case stress concentration factor is ignored?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Use of multiple notches in a V shaped flat plate will

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Determine the torsional shear stress in the welds if P=8kN and thickness of the welds is assumed t.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

In distortion energy theorem, if a unit cube is subjected to biaxial stress, then S(yt) is given by which of the following?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Tolerance for a shaft of 50mm diameter as the basic size, with the fundamental deviation denoted by g and tolerance of grade 7 is represented as?

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate the bending stress in the welds if P=40kN, leg=4mm and e=400mm.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stresses due to shrink shift in jacket.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the tangential stress in compound cylinder.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stress due to shrink shift in inner tube.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate size of the welds if P=40kN, leg=4mm and e=400mm. Maximum permissible value of shear stress in the weld is 70N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the radial stress in compound cylinder.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Determine the secondary shear stress acting on the bolt 3 and its direction. The bolts are equidistant having separated by 60mm and the margin to the left and right is 25mm.Also P=5kN acts at a distance of 200mm from the channel.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.

asked Jan 22 in Machine Design by Carter (86.7k points)

...