In which of the following case stress concentration factor is ignored?

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

+1 vote

1 answer

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is?

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Use of multiple notches in a V shaped flat plate will

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The stress represented by sin (t) + 4 belongs to which category?

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The stress represented by cos (t) belongs to which category?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The stress represented by sin (t) + 1 belongs to which category?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Stress intensity factor is the critical value of stress at which crack extension occurs.

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. If permissible bending stress is 500N/mm², then calculate the beam strength.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

While considering moment of inertia for calculating torsional shear stress, J=I(xx) + I(yy), which of the following can be neglected in context with the following figure?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

In distortion energy theorem, if a unit cube is subjected to biaxial stress, then S(yt) is given by which of the following?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Inaccuracies in tooth profile lead to concentration of pressure on the middle of tooth.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Yield strength is defined as the maximum stress at which a marked increase in elongation occurs without increase in________

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm²Find the maximum amount of shear stress to which the body is subjected.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

According to principal stress theory, which option represents the correct relation between yield strength in shear (YSS) and the yield strength in tension (YST)?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The temperature at which new stress free grains are formed in the metal is called the ______ temperature.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In design of wire ropes, bending stress is converted into an equivalent bending load which is given by [d= diameter of individual wire and D= diameter of sheave].

asked Jan 21 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The net axial force acting on bearing is zero in case of double helical gears while none zero in case of herringbone gears.

asked 3 days ago in Machine Design by Carter (86.7k points)

...