Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross-section and highest value of actual stress near discontinuity.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

+1 vote

1 answer

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is?

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In which of the following case stress concentration factor is ignored?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Is it logical to use fluid analogy to understand the phenomenon of stress concentration?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Use of multiple notches in a V shaped flat plate will

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The stress represented by sin (t) + 2 belongs to which category?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The stress represented by sin (t) + 4 belongs to which category?

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The stress represented by cos (t) belongs to which category?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The stress represented by sin (t) + 1 belongs to which category?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If for a curved beam of trapezoidal cross section, radius of neutral axis is 89.1816mm and radius of centroidal axis is 100mm, then find the bending stress at inner fibre whose radius is 50mm. Area of cross section of beam is 7200mm² and the beam is loaded with 100kN of load.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering combined effect of direct stress and bending stress.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Slenderness ratio is [l= length of column and k= least radius of gyration of cross section about its axis].

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Fatigue failure is time dependent failure.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The buttresses of a free deck buttress dam are provided at ‘x’ m clear spacing and buttress thickness is proposed to be ‘t’ m. The buttress section can then be designed like the section of a concrete gravity dam by considering the effective unit weight of water = Surcharge factor (S) x actual unit weight of water. The value of this surcharge factor is given as _____________

asked Sep 25, 2023 in Irrigation Engineering by Carter (89.5k points)

0 votes

0 answers

The load shared by each spring is inversely proportional to the cross section of wire.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Stress intensity factor is the critical value of stress at which crack extension occurs.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate size of the welds if P=40kN, leg=4mm and e=400mm. Maximum permissible value of shear stress in the weld is 70N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

...