Slenderness ratio is [l= length of column and k= least radius of gyration of cross section about its axis].

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

+1 vote

1 answer

Columns with what slenderness ratio are not designed with respect to buckling but are designed for compressive stresses.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Steel columns with a slenderness ratio of 95 are

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If slenderness ratio=45, which mode of failure will dominate?

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Short column and long column are classified on the basis of

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Piston rod is an example of column.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Bucking of column means

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Which of the following are true for End fixity coefficient

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If for a curved beam of trapezoidal cross section, radius of neutral axis is 89.1816mm and radius of centroidal axis is 100mm, then find the bending stress at inner fibre whose radius is 50mm. Area of cross section of beam is 7200mm² and the beam is loaded with 100kN of load.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A wooden cylinder of sp.gr. = 0.6 and circular in cross-section is required to float in oil(sp.gr. = 0.90). Find the L/D ratio for the cylinder to float with its longitudinal axis vertical in oil, where L is the height of cylinder and D is its diameter.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (122k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If magnitude of contact pressure between sealing lip and rotating shaft is very high then

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In design of wire ropes, bending stress is converted into an equivalent bending load which is given by [d= diameter of individual wire and D= diameter of sheave].

asked Jan 21 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In order to find the radius of gyration of a car, it is suspended with its axis vertical from three parallel wires 2.5 metres long. The wires are attached to the rim at points spaced 120° apart and at equal distances 250 mm from the axis. It is found that the wheel makes 50 torsional oscillations of small amplitude about its axis in 170 seconds. Find the radius of gyration of the wheel.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Calculate the moment of inertia and radius of gyration of a solid sphere of mass 10 kg and diameter 6.5m about its centroidal axis.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

0 votes

0 answers

Which type of rope drum is preferred?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

An oil seal is a mechanical device made of elastic material which is used to prevent leakage of fluid between two machine components.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Wire rope specified as 8×10. Calculate the number of strands.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Class 1 pressure vessels are used to contain

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

An unfired pressure vessel is used to carry stem, gases or fluids at pressure

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If the radius of gyration of a compound pendulum about an axis through c.g. is more, then its frequency of oscillation will be

asked Sep 23, 2022 in Machine Kinematics by Leo (38.0k points)

0 votes

0 answers

A solid cast iron disk of mass 1000kg is rotating at 350rpm. Diameter of the disk is 1m and time taken to come to stop the disk by brake is 1.6sec.Square of radius of gyration is 0.2. Calculate the angle through which disk rotated during braking period.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A solid cast iron disk of mass 1000kg is rotating at 350rpm. Diameter of the disk is 1m and time taken to come to stop the disk by brake is 1.6sec.Square of radius of gyration is 0.2. Calculate the torque capacity of the brake.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A solid cast iron disk of mass 1000kg is rotating at 350rpm. Diameter of the disk is 1m and time taken to come to stop the disk by brake is 1.6sec.Square of radius of gyration is 0.2. Calculate the average angular velocity during braking period.

asked Jan 22 in Machine Design by Carter (86.7k points)

...