An unfired pressure vessel is used to carry stem, gases or fluids at pressure

Question

An unfired pressure vessel is used to carry stem, gases or fluids at pressure

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Class 1 pressure vessels are used to contain

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

An oil seal is a mechanical device made of elastic material which is used to prevent leakage of fluid between two machine components.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If magnitude of contact pressure between sealing lip and rotating shaft is very high then

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Does oil seal consist of any spring in its structure?

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Wire rope specified as 8×10. Calculate the number of strands.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Piston rod is an example of column.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In design of wire ropes, bending stress is converted into an equivalent bending load which is given by [d= diameter of individual wire and D= diameter of sheave].

asked Jan 21 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Columns with what slenderness ratio are not designed with respect to buckling but are designed for compressive stresses.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which type of rope drum is preferred?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Slenderness ratio is [l= length of column and k= least radius of gyration of cross section about its axis].

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Bucking of column means

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Short column and long column are classified on the basis of

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Steel columns with a slenderness ratio of 95 are

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following are true for End fixity coefficient

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If slenderness ratio=45, which mode of failure will dominate?

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If circumferential stress is P, then longitudinal stress in the pressure vessel is?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The pressure intensity at an element on long shoe brake varies directly with the sin of the pressure angle of the element of friction lining.

asked Jan 21 in Machine Design by Chris (52.6k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Longer arm is of length 500mm. Calculate the reaction or force acting on the fulcrum.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Trapezoidal threads are better than square threads as there is radial pressure or side thrust on the nut.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stresses due to shrink shift in jacket.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the tangential stress in compound cylinder.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stress due to shrink shift in inner tube.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the radial stress in compound cylinder.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the length of the pin.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the shear stress in the pin.

asked Jan 25 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-02-02T14:08:42+0000

Suitable answer is (b) Greater than atmospheric pressure

Unlock profound understanding with: Terminology.

An unfired pressure vessel is used to carry stem, gases or fluids at pressure

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories