Class 1 pressure vessels are used to contain

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

An unfired pressure vessel is used to carry stem, gases or fluids at pressure

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

An oil seal is a mechanical device made of elastic material which is used to prevent leakage of fluid between two machine components.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If magnitude of contact pressure between sealing lip and rotating shaft is very high then

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Wire rope specified as 8×10. Calculate the number of strands.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Columns with what slenderness ratio are not designed with respect to buckling but are designed for compressive stresses.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Short column and long column are classified on the basis of

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Steel columns with a slenderness ratio of 95 are

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Which of the following are true for End fixity coefficient

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Piston rod is an example of column.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which type of rope drum is preferred?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Slenderness ratio is [l= length of column and k= least radius of gyration of cross section about its axis].

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Bucking of column means

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If slenderness ratio=45, which mode of failure will dominate?

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In design of wire ropes, bending stress is converted into an equivalent bending load which is given by [d= diameter of individual wire and D= diameter of sheave].

asked Jan 21 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Which of the following contain copper

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the operating force in the clutch.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform pressure theory, calculate the operating force in the clutch.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the torque transmitting capacity of the clutch.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Refer to fig 1. Two plates are fastened by means of two bolts. The yield strength of bolt is 400N/mm² and factor of safety is 4. Determine the size of the bolts.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which bolt is under maximum stress if dowel pins are used to relieve cap screws from shear stress?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Worm gear drives are used to transmit power between two non-intersecting shafts which are generally at right angles to each other.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the axial component of gear tooth force if power transmitted is 6kW and diameters of pinion and gear are 150mm and 210 mm with face width of tooth being 35mm. Power is transmitted at 3000rpm. Also pressure angle is 20⁰.

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Trapezoidal threads are better than square threads as there is radial pressure or side thrust on the nut.

asked Jan 23 in Machine Design by Carter (86.7k points)

...