Does oil seal consist of any spring in its structure?

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

An oil seal is a mechanical device made of elastic material which is used to prevent leakage of fluid between two machine components.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Wire rope specified as 8×10. Calculate the number of strands.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Class 1 pressure vessels are used to contain

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

An unfired pressure vessel is used to carry stem, gases or fluids at pressure

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If magnitude of contact pressure between sealing lip and rotating shaft is very high then

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Slenderness ratio is [l= length of column and k= least radius of gyration of cross section about its axis].

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In design of wire ropes, bending stress is converted into an equivalent bending load which is given by [d= diameter of individual wire and D= diameter of sheave].

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Piston rod is an example of column.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which type of rope drum is preferred?

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Bucking of column means

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Short column and long column are classified on the basis of

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Columns with what slenderness ratio are not designed with respect to buckling but are designed for compressive stresses.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Steel columns with a slenderness ratio of 95 are

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following are true for End fixity coefficient

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If slenderness ratio=45, which mode of failure will dominate?

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Silicon addition in spring steel increases its toughness.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the transverse pressure angle in degrees.

asked 1 day ago in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A compound screw consist of two screws in parallel such that the resultant motion is the summation of the individual motion of screws.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. Calculate the material constant K if surface hardness is 400BHN.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of pinion.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the ratio factor Q if a pair of bevel gear consist of 25 teeth pinion meshing with a 40 teeth gear.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the dedendum circle diameter of the pinion.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

The cross section of V belt consist of rubber backing to help engagement of teeth with sprocket.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of the gear.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Needles bearing consist of rollers of small diameter and very small length.

asked Jan 27 in Machine Design by Carter (89.5k points)

...