Needles bearing consist of rollers of small diameter and very small length.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

A rolling contact bearing is specified as X307. Determine the series.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Stribeck equation gives dynamic load capacity of the bearing.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following is expression for stribeck equation?(Number of balls=z)?

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the dedendum circle diameter of the pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of the gear.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate addendum circle diameter of the pinion.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate pitch circle diameter of the pinion.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. Calculate the material constant K if surface hardness is 400BHN.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the transverse pressure angle in degrees.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. If permissible bending stress is 500N/mm², then calculate the beam strength.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of helical gears consist of 25 teeth pinion gear meshing with a 90 teeth gear. Calculate the wear strength If surface hardness is 260BHN. Also face width=35mm, module=4mm and helix angle=25⁰.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A clearance bearing is design accurately to keep the radius of journal and bearing equal.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of helical gears consist of 25 teeth pinion gear meshing with a 90 teeth gear. Calculate the material constant k If surface hardness is 260BHN.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate the centre distance.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Cycloidal teeth consist of

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate the addendum.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate the tooth thickness.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Angular contact bearing can take thrust as well as radial loads.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The net axial force acting on bearing is zero in case of double helical gears while none zero in case of herringbone gears.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Fitted bearing must be partial bearing.

asked Jan 25 in Machine Design by Carter (89.5k points)

...