A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft.

Question

A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft.

1 Answer

Related questions

+1 vote

1 answer

The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Stribeck equation gives dynamic load capacity of the bearing.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Needles bearing consist of rollers of small diameter and very small length.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following is expression for stribeck equation?(Number of balls=z)?

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A rolling contact bearing is specified as X307. Determine the series.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A radial bearing supports the load that acts along the axis of the shaft.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the dedendum circle diameter of the pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of the gear.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate addendum circle diameter of the pinion.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Crossed helical gears have very low load carrying capacity.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Deep groove ball bearings creates a lot of noise.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

There is problem of alignment in deep groove ball bearings.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Deep groove ball bearing has immense rigidity.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the transverse pressure angle in degrees.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If centre distance between the two gears on same shaft is unequal to the centre distance on the other two gears on the second shaft, then this gear train is called reverted gear train.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The teeth of the helical gears are cut parallel to the shaft axis.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate pitch circle diameter of the pinion.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. Calculate the material constant K if surface hardness is 400BHN.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. If permissible bending stress is 500N/mm², then calculate the beam strength.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

In angular contact bearings, ____ bearings are required to take thrust load in both directions.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The direction of tangential component for a driving gear is same to the direction of rotation.

asked Jan 21 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-02-02T14:35:20+0000

The appropriate answer is (a) True

Simplify with an easy explanation: Permissible magnitude of deformation is set as per the experimental data.

A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories