Fatigue failure is time dependent failure.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The stress represented by sin (t) + 2 belongs to which category?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

The stress represented by sin (t) + 4 belongs to which category?

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The stress represented by cos (t) belongs to which category?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The stress represented by sin (t) + 1 belongs to which category?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Propagation of fatigue failure is always due to compressive stresses.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Is it logical to use fluid analogy to understand the phenomenon of stress concentration?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross-section and highest value of actual stress near discontinuity.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Use of multiple notches in a V shaped flat plate will

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is?

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In which of the following case stress concentration factor is ignored?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Failure in rivet occurs by which mode?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

For cast iron components, which of the following strength are considered to be the failure criterion?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The wear strength indicates the maximum value of radial force at the large end of the tooth that the tooth can transmit without pitting failure.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If slenderness ratio=45, which mode of failure will dominate?

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

For components made of ductile materials like steel, subjected to static loading which of the following strength is used as a failure of criterion?

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Lame’s equation used to find the thickness of the cylinder is based on maximum strain failure.

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Is use of a flywheel recommended when a large motor is required only for a small instant of time?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

A solid cast iron disk of mass 1000kg is rotating at 350rpm. Diameter of the disk is 1m and time taken to come to stop the disk by brake is 1.6sec.Square of radius of gyration is 0.2. Calculate the angle through which disk rotated during braking period.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A solid cast iron disk of mass 1000kg is rotating at 350rpm. Diameter of the disk is 1m and time taken to come to stop the disk by brake is 1.6sec.Square of radius of gyration is 0.2. Calculate the torque capacity of the brake.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A solid cast iron disk of mass 1000kg is rotating at 350rpm. Diameter of the disk is 1m and time taken to come to stop the disk by brake is 1.6sec.Square of radius of gyration is 0.2. Calculate the average angular velocity during braking period.

asked Jan 22 in Machine Design by Carter (89.5k points)

...