If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm²Find the maximum amount of shear stress to which the body is subjected.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm². Find the minimum normal stress.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

The total strain energy for a unit cube subjected to three principal stresses is given by?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Calculate the diameter of pin from shear consideration with maximum shear stress allowed is 40NN/mm² and an axial tensile force of 50kN is acting on the rod.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The normal stress is perpendicular to the area under considerations, while the shear stress acts over the area.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stresses due to shrink shift in jacket.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the tangential stress in compound cylinder.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the radial stress in compound cylinder.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the shear stress in the pin.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Maximum Principal Stress Theory is not good for brittle materials.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stress due to shrink shift in inner tube.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the interference [E=210kN/mm²].

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the shrinkage pressure.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the diameter of the rivets by shear considerations if permissible shear stress in rivets is 60N/mm² and P=15kN.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A beam subjected to bending moment undergoes which of the following stresses?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the diameter of the rivets if permissible shear stress is 60N/mm². Bolts are separated by 100mm and force P=30kN.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm².

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

According to principal stress theory, which option represents the correct relation between yield strength in shear (YSS) and the yield strength in tension (YST)?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate size of the welds if P=40kN, leg=4mm and e=400mm. Maximum permissible value of shear stress in the weld is 70N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In cold riveting like hot riveting shank is subjected to majorly tensile stress.

asked Jan 22 in Machine Design by Carter (86.7k points)

...