Shank is the portion of bolt between the head and the thread.

Question

Shank is the portion of bolt between the head and the thread.

← Prev Question Next Question →

1 Answer

Related questions

0 votes

0 answers

In nut and bolt fastener, nut is generally held stationary while bolt is rotated.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Fillister, button, flat and hexagonal heads are all tightened externally.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following is not a function of washer?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If there is no place to accommodate the nut, then one would choose the

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following are good for parts that are seldom dismantled.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Set screws are subjected to tensile forces only.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Refer to fig 1. Two plates are fastened by means of two bolts. The yield strength of bolt is 400N/mm² and factor of safety is 4. Determine the size of the bolts.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Determine the secondary shear stress acting on the bolt 3 and its direction. The bolts are equidistant having separated by 60mm and the margin to the left and right is 25mm.Also P=5kN acts at a distance of 200mm from the channel.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the radius of Mohr circle which can be made from the shear stress and tensile stress acting on bolts.(Consider bolt under max stress and area of bolt is A)

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the screw torque in terms of clamping force W if nominal diameter=22mm and pitch=5mm.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the overall efficiency if nominal diameter=22mm and pitch=5mm.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the clamping force W if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the collar torque in terms of clamping force W assuming uniform wear theory if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If the length of the shank is doubled, then strain energy absorbed by shank

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Two plates each of thickness t are to be riveted together. If length of shank portion necessary to form the closing head is a, then length of rivet shank is given by?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the size of the bolt using maximum principal stress theory.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If core diameter of bolt is 13.8cm the it’s nominal diameter is given by?

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which bolt is under maximum shear stress?

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which bolt is under maximum stress if dowel pins are used to relieve cap screws from shear stress?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which bolt is used a criterion for designing?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Determine the angle θ so that the force in the bolt 1 has maximum value.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which bolt can be used as criteria for designing?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If for a trapezoidal thread, angle of thread is 15’ then what will be the replacement of the coefficient of friction which is 0.15.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If distance between the bolts from the axis of tilting is 125mm and 25mm, then find the effective tensile force acting on the bolts lying at 125mm from tilting axis.

asked Jan 23 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-02-02T14:29:16+0000

The best answer is (a) True

Explanation: Shank is the portion between head and the thread of the bolt.

Shank is the portion of bolt between the head and the thread.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories