Fillister, button, flat and hexagonal heads are all tightened externally.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Which of the following are good for parts that are seldom dismantled.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Set screws are subjected to tensile forces only.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

In nut and bolt fastener, nut is generally held stationary while bolt is rotated.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Shank is the portion of bolt between the head and the thread.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If there is no place to accommodate the nut, then one would choose the

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the overall efficiency if nominal diameter=22mm and pitch=5mm.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Refer to fig 1. Two plates are fastened by means of two bolts. The yield strength of bolt is 400N/mm² and factor of safety is 4. Determine the size of the bolts.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

For a double threaded screw, what will be the tangent of helix angle if nominal diameter and pitch are 100mm and 12mm respectively?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the clamping force W if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Determine the secondary shear stress acting on the bolt 3 and its direction. The bolts are equidistant having separated by 60mm and the margin to the left and right is 25mm.Also P=5kN acts at a distance of 200mm from the channel.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the collar torque in terms of clamping force W assuming uniform wear theory if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The efficiency of flat belt drive is 35%. If all the parameters are same and flat belt is replaced by V belt, than the efficiency of V belt will be?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

How many types of jacks are there which can be used in a screw jack?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which of the following statements are true about eccentrically loaded circular base?

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which bolt is under maximum stress if dowel pins are used to relieve cap screws from shear stress?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Find the ratio of the effective tensile load to which the two bolts are subjected.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In a differential screw, two screws are connected in series such that the resultant motion is the summation of the motion of the two screws.

asked Jan 21 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also given pitch=8mm and coefficient of friction is 0.15.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Crests and roots of the threads may lead to leakage in fluid tight threads if flattened or rounded to a circular arc.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If bending stress in a screw is of magnitude 95N/mm² and torsional shear stress of magnitude 15N/mm², then what is the principal shear stress?

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

What is the output from differential screws when pitch of the two screws is 12mm and 8mm? Also the nut is rotated by applying a force of 120N at a radius of 300mm and the two screws remain stationary. The torque of raising and lowering for the two screws is 5k N-mm and 2.5k N-mm where k is the effective axial weight on the screw.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If distance between the bolts from the axis of tilting is 125mm and 25mm, then find the effective tensile force acting on the bolts lying at 125mm from tilting axis.

asked Jan 23 in Machine Design by Carter (86.7k points)

...