Find the ratio of the effective tensile load to which the two bolts are subjected.

Question

Find the ratio of the effective tensile load to which the two bolts are subjected.

← Prev Question Next Question →

1 Answer

Related questions

0 votes

0 answers

Find the effective tensile force acting in the two bolts.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If distance between the bolts from the axis of tilting is 125mm and 25mm, then find the effective tensile force acting on the bolts lying at 125mm from tilting axis.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the radius of Mohr circle which can be made from the shear stress and tensile stress acting on bolts.(Consider bolt under max stress and area of bolt is A)

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the principal shear stress in the top bolts in terms of area A?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Determine the size of bolts using maximum shear stress theory.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the size of the bolt using maximum principal stress theory.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which bolt is used a criterion for designing?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which bolt can be used as criteria for designing?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Set screws are subjected to tensile forces only.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Refer to fig 1. Two plates are fastened by means of two bolts. The yield strength of bolt is 400N/mm² and factor of safety is 4. Determine the size of the bolts.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Determine the secondary shear stress acting on the bolt 3 and its direction. The bolts are equidistant having separated by 60mm and the margin to the left and right is 25mm.Also P=5kN acts at a distance of 200mm from the channel.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the effective force in vector form to which rivet 4 is subjected. Bolts are separated by 100mm and force P=30kN.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the effective force in vector form to which rivet 2 is subjected. Bolts are separated by 100mm and force P=30kN.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

What is the output from differential screws when pitch of the two screws is 12mm and 8mm? Also the nut is rotated by applying a force of 120N at a radius of 300mm and the two screws remain stationary. The torque of raising and lowering for the two screws is 5k N-mm and 2.5k N-mm where k is the effective axial weight on the screw.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

What is the efficiency of differential screws when pitch of the two screws is 12mm and 8mm? The nut is rotated by applying a force of 120N at a radius of 300mm and the two screws remain stationary. The torque of raising and lowering for the two screws is 5k N-mm and 2.5k N-mm where k is the effective axial weight on the screw.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also given pitch=8mm and coefficient of friction is 0.15.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Arrange the bolts in order of decreasing shear stresses.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

In figure 2, determine the size of the bolts.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The shock absorbing capacity of bolts can be increased by

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In a differential screw, two screws are connected in series such that the resultant motion is the summation of the motion of the two screws.

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the screw torque in terms of clamping force W if nominal diameter=22mm and pitch=5mm.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the overall efficiency if nominal diameter=22mm and pitch=5mm.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the clamping force W if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-01-27T10:49:52+0000

The correct answer is (b) 10

Here's an easy explanation: F₁=Pel₁/2(l₁² + l₂²) and F₂= Pel₂/2(l₁² + l₂²) or F₁/F₂ =l₁/ l₂.

Find the ratio of the effective tensile load to which the two bolts are subjected.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories