Can the cotter joint be used to connect slide spindle and fork of valve mechanism?

Question

Can the cotter joint be used to connect slide spindle and fork of valve mechanism?

← Prev Question Next Question →

1 Answer

Related questions

0 votes

0 answers

Cotter joint is used when the members are subjected to which type of stresses?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The principle of wedge action is used in cotter joint.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In cold riveting like hot riveting shank is subjected to majorly tensile stress.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Knuckle Joint can’t be used to connect two intersecting rods.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Cold riveting holds the connected parts better than hot riveting.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A maximum of how many roads may be connected using a knuckle joint?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are important parts of knuckle joint?

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

For components made of ductile materials like steel, subjected to static loading which of the following strength is used as a failure of criterion?

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

For cast iron components, which of the following strength are considered to be the failure criterion?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 10N/mm². Find the inclination of the plane in which shear stress is maximal.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the length of the pin.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm²Find the maximum amount of shear stress to which the body is subjected.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

According to principal stress theory, which option represents the correct relation between yield strength in shear (YSS) and the yield strength in tension (YST)?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm². Find the minimum normal stress.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the shear stress in the pin.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If there are residual stresses in the material, than lower factor of safety is used.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering combined effect of direct stress and bending stress.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A curved beam has neutral axis is curved while loaded and straight when unloaded.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If for a curved beam of trapezoidal cross section, radius of neutral axis is 89.1816mm and radius of centroidal axis is 100mm, then find the bending stress at inner fibre whose radius is 50mm. Area of cross section of beam is 7200mm² and the beam is loaded with 100kN of load.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

asked Jan 23 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-01-27T10:57:10+0000

Correct option is (a) True

Discover the easiest explanation: As long as axial forces act, cotter joint can be employed.

Can the cotter joint be used to connect slide spindle and fork of valve mechanism?

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories