If there is no place to accommodate the nut, then one would choose the

Question

If there is no place to accommodate the nut, then one would choose the

← Prev Question Next Question →

1 Answer

Related questions

0 votes

0 answers

In nut and bolt fastener, nut is generally held stationary while bolt is rotated.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Set screws are subjected to tensile forces only.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Shank is the portion of bolt between the head and the thread.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Which of the following are good for parts that are seldom dismantled.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Fillister, button, flat and hexagonal heads are all tightened externally.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

What is the output from differential screws when pitch of the two screws is 12mm and 8mm? Also the nut is rotated by applying a force of 120N at a radius of 300mm and the two screws remain stationary. The torque of raising and lowering for the two screws is 5k N-mm and 2.5k N-mm where k is the effective axial weight on the screw.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

What is the efficiency of differential screws when pitch of the two screws is 12mm and 8mm? The nut is rotated by applying a force of 120N at a radius of 300mm and the two screws remain stationary. The torque of raising and lowering for the two screws is 5k N-mm and 2.5k N-mm where k is the effective axial weight on the screw.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

The transverse shear stress at the root of the threads in the nut can be given by?(symbols have their usual meaning, z=number of threads in nut)

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If the length of the shank is doubled, then strain energy absorbed by shank

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If bending stress in a screw is of magnitude 95N/mm² and torsional shear stress of magnitude 15N/mm², then what is the principal shear stress?

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If distance between the bolts from the axis of tilting is 125mm and 25mm, then find the effective tensile force acting on the bolts lying at 125mm from tilting axis.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If for a trapezoidal thread, angle of thread is 15’ then what will be the replacement of the coefficient of friction which is 0.15.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

How many types of jacks are there which can be used in a screw jack?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Crests and roots of the threads may lead to leakage in fluid tight threads if flattened or rounded to a circular arc.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which bolt is under maximum stress if dowel pins are used to relieve cap screws from shear stress?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the overall efficiency if nominal diameter=22mm and pitch=5mm.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If core diameter of bolt is 13.8cm the it’s nominal diameter is given by?

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

For a double threaded screw, what will be the tangent of helix angle if nominal diameter and pitch are 100mm and 12mm respectively?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the clamping force W if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the collar torque in terms of clamping force W assuming uniform wear theory if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also given pitch=8mm and coefficient of friction is 0.15.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Refer to fig 1. Two plates are fastened by means of two bolts. The yield strength of bolt is 400N/mm² and factor of safety is 4. Determine the size of the bolts.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Referring to fig 2, Determine the primary shear force.

asked Jan 23 in Machine Design by Carter (86.7k points)

Chris · Answer 1 · 2026-01-27T14:19:26+0000

Right answer is (b) Tap Bolts

Get the lowdown with: Tap bolts are directly threaded into the clamped parts and does not require any nut.

If there is no place to accommodate the nut, then one would choose the

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories