Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate size of the welds if P=40kN, leg=4mm and e=400mm. Maximum permissible value of shear stress in the weld is 70N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate the bending stress in the welds if P=40kN, leg=4mm and e=400mm.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate width of the band if permissible tensile stress is 80N/mm². Force P=15kN and diameter of the rivet can be taken as 9mm. Given thickness=3mm

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by crushing consideration if permissible compression stress in rivets is 120N/mm², thickness of plate 3mm and P=15kN.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the direct shear stress in the welds by ignoring torsional shear stress if P=8kN and thickness of weld is 5mm.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Determine the torsional shear stress in the welds if P=8kN and thickness of the welds is assumed t.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by shear considerations if permissible shear stress in rivets is 60N/mm² and P=15kN.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If secondary shear stress acting on any bolts is given by Cxr₁ where r₁ is the distance of bolt from CG, then find the value of C. Bolts are equidistant with spacing of 100mm. Force P=30kN.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Magnetic crack detection method in the welds is destructible examination.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Two plates each of thickness t are to be riveted together. If length of shank portion necessary to form the closing head is a, then length of rivet shank is given by?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The following bracket is welded to the vertical column. The joint undergoes torsional stresses.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the length of weld 1 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the total length of weld required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the length of weld 2 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If length of weld is l and leg h, then area of throat can be given by

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets if permissible shear stress is 60N/mm². Bolts are separated by 100mm and force P=30kN.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the primary shear stress on each rivet if P=30kN and diameter of rivets is 15mm.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If circumferential stress is P, then longitudinal stress in the pressure vessel is?

asked Jan 23 in Machine Design by Carter (89.5k points)

...