Find the total length of weld required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

Question

Find the total length of weld required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

← Prev Question Next Question →

1 Answer

Related questions

0 votes

0 answers

Find the length of weld 1 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the length of weld 2 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the direct shear stress in the welds by ignoring torsional shear stress if P=8kN and thickness of weld is 5mm.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate size of the welds if P=40kN, leg=4mm and e=400mm. Maximum permissible value of shear stress in the weld is 70N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

While considering moment of inertia for calculating torsional shear stress, J=I(xx) + I(yy), which of the following can be neglected in context with the following figure?

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Determine the torsional shear stress in the welds if P=8kN and thickness of the welds is assumed t.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the shear stress in the pin.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by shear considerations if permissible shear stress in rivets is 60N/mm² and P=15kN.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets if permissible shear stress is 60N/mm². Bolts are separated by 100mm and force P=30kN.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which equations can be used to find the resisting force in the two welds?

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by crushing consideration if permissible compression stress in rivets is 120N/mm², thickness of plate 3mm and P=15kN.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate width of the band if permissible tensile stress is 80N/mm². Force P=15kN and diameter of the rivet can be taken as 9mm. Given thickness=3mm

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

For the following welded joint l₁y₁=l₂y₂.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The moment of forces about the CG is ?

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The following welded joint is an example of

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If secondary shear stress acting on any bolts is given by Cxr₁ where r₁ is the distance of bolt from CG, then find the value of C. Bolts are equidistant with spacing of 100mm. Force P=30kN.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the length of the pin.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal.

asked Jan 25 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-01-27T11:01:42+0000

The correct choice is (c) 202.06mm

Delve into insight with: 100000=0.707x10xlx70.

Find the total length of weld required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories