The moment of forces about the CG is ?

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

While considering moment of inertia for calculating torsional shear stress, J=I(xx) + I(yy), which of the following can be neglected in context with the following figure?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

For the following welded joint l₁y₁=l₂y₂.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the direct shear stress in the welds by ignoring torsional shear stress if P=8kN and thickness of weld is 5mm.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which equations can be used to find the resisting force in the two welds?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the length of weld 1 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Determine the torsional shear stress in the welds if P=8kN and thickness of the welds is assumed t.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The following welded joint is an example of

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the total length of weld required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the length of weld 2 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If secondary shear stress acting on any bolts is given by Cxr₁ where r₁ is the distance of bolt from CG, then find the value of C. Bolts are equidistant with spacing of 100mm. Force P=30kN.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Are the rivets subjected any bending moment in case of lap joint?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Moment of normal force and frictional forces about the pivot axis are 640000N-mm and 250000N-mm respectively. If force acts at a distance of 190mm from the pivoted point, calculate the actuating force.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Failure in rivet occurs by which mode?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the tensile strength of rivets along B-B.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are used in light sheet metal work?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the effective force in vector form to which rivet 4 is subjected. Bolts are separated by 100mm and force P=30kN.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Magnetic crack detection method in the welds is destructible examination.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Two plates each of thickness t are to be riveted together. If length of shank portion necessary to form the closing head is a, then length of rivet shank is given by?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Forge welding involves heating of parts to elastic stage and joint is prepared by impact force.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Are the bolts 2 and 3 under same force?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

The capacity of welded structures to damp vibrations is quite good.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate the bending stress in the welds if P=40kN, leg=4mm and e=400mm.

asked Jan 27 in Machine Design by Carter (89.5k points)

...