A strap is used in a lap joint which is riveted to each of the two plates.

Question

A strap is used in a lap joint which is riveted to each of the two plates.

1 Answer

Related questions

0 votes

0 answers

Two plates each of thickness t are to be riveted together. If length of shank portion necessary to form the closing head is a, then length of rivet shank is given by?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Lozenge joint is a kind of lap joint.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Are the rivets subjected any bending moment in case of lap joint?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are used in light sheet metal work?

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following rivet head consist of frustum of cone attached to the shank?

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Failure in rivet occurs by which mode?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Among flat head and snap head rivet, which has the higher head height?

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by crushing consideration if permissible compression stress in rivets is 120N/mm², thickness of plate 3mm and P=15kN.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the diameter of the rivets by shear considerations if permissible shear stress in rivets is 60N/mm² and P=15kN.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate width of the band if permissible tensile stress is 80N/mm². Force P=15kN and diameter of the rivet can be taken as 9mm. Given thickness=3mm

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

What is the other name for pitch?

asked Jan 21 in Machine Design by Chris (52.6k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The two plates are welded as shown in the figure 1. It is an example of

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which equations can be used to find the resisting force in the two welds?

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Forge welding involves heating of parts to elastic stage and joint is prepared by impact force.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The following bracket is welded to the vertical column. The joint undergoes torsional stresses.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

For the following welded joint l₁y₁=l₂y₂.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate efficiency of the joint.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The following welded joint is an example of

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The amount by which the two rods to be joined are drawn together is called as?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate the bending stress in the welds if P=40kN, leg=4mm and e=400mm.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate size of the welds if P=40kN, leg=4mm and e=400mm. Maximum permissible value of shear stress in the weld is 70N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-01-27T10:33:49+0000

Accurate option is (b) False

For the easiest explanation: That joint is called butt joint.

A strap is used in a lap joint which is riveted to each of the two plates.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories