For an ordinary clay of medium sensitivity, the value of compression index is _____ if liquid limit is 50%.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

For an ordinary clay of medium to low sensitivity, the value of Cc corresponding to the field consolidation line is roughly equal to __________ the compression index of remolded sample.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

For a remolded sample of clay with liquid limit of 45%, find its compression index.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

The Cc for ordinary clay of medium to low sensitivity, the value of Cc corresponding to the field consolidation line is given by ______

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

Two clay layer of A and B of thickness 2cm and 3 cm is load with pressure of 200KN/m^2. If the time taken by soil A to reach 50% consolidation is 1/4^th of that required by soil B to reach 50% consolidation, then find the ratio of coefficients of Permeability. Given that ratio of coefficient of volume change is 1.751.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

Two clay layer of A and B of thickness 2cm and 3 cm is load with pressure of 200KN/m^2. If the time taken by soil A to reach 50% consolidation is 1/4^th of that required by soil B to reach 50% consolidation, then find the ratio of coefficients of consolidation.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If initial voids ratio is 1.08, then find the compression index.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

A clay sample in laboratory test has 24mm thickness. It is tested with single drainage and consolidated 50%. The clay layer from which sample was obtained is 4m thick. Find the time to consolidate 50% with single drainage.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

A clay sample in laboratory test has 24mm thickness. It is tested with double drainage and consolidated 50%. The clay layer from which sample was obtained is 4m thick. Find the time to consolidate 50% with single drainage.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

A clay sample in laboratory test has 24mm thickness. It is tested with single drainage and consolidated 50%. The clay layer from which sample was obtained is 4m thick. Find the time to consolidate 50% with double drainage.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

A clay sample in laboratory test has 24mm thickness. It is tested with double drainage and consolidated 50%. The clay layer from which sample was obtained is 4m thick. Find the time to consolidate 50% with double drainage.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

A clay sample 24mm thick takes 20 minutes to consolidate 50% with single drainage. The field clay layer from which sample was obtained takes 386 days to consolidate 50% with single drainage. Find the depth of the clay layer in the field.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

A clay sample 24mm thick takes 20 minutes to consolidate 50% with double drainage. The field clay layer from which sample was obtained takes 386 days to consolidate 50% with double drainage. Find the depth of the clay layer in the field.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

A clay sample 24mm thick takes 20 minutes to consolidate 50% with single drainage. The field clay layer from which sample was obtained takes 386 days to consolidate 50% with double drainage. Find the depth of the clay layer in the field.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

A clay sample 24mm thick takes 20 minutes to consolidate 50% with double drainage. The field clay layer from which sample was obtained takes 386 days to consolidate 50% with single drainage. Find the depth of the clay layer in the field.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If a clay layer is expected to settle 12cm under loading settles 3cm at the end of one month, then find the degree of consolidation.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

For the consolidation of 50%, find the time factor.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If the height of soil specimen is reduced from 0.28 cm to 1.926cm due to an increment of load of 100KN/ m^2. Find the coefficient of volume change.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If the final water content is 30% and specific gravity is 2.65 for a soil sample, then its final void ratio is _________

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If the initial voids ratio is 0.964 for a layer of height 100cm. It is located with 200KN/m^2 and the void ratio becomes 0.822. Find the settlement.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If the final voids ratio is 0.864 for a soil sample of specific gravity 2.7, then its final water content will be _______________

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If a soil A has coefficient of volume change as 0.536m^2/MN and the ratio of coefficient of volume change of A and B soils is 1.845, then find mv for soil B.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If height of solids Hs is 6.725mm, mass is 180.4g with specific gravity G=2.68, then final the Cross-sectional area of specimen.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If excess hydraulic pressure is 19.62 KN/m^2 then find the hydraulic head.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

A soil sample is having voids ratio 0.72 under a pressure of 200KN/m^2. If the void ratio is reduced to 0.5 under 450kn/m^2 load, then find the change in effective pressure.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

+1 vote

1 answer

If the specimen height H is 24mm and height of solids Hs is 13.45mm, then find the voids ratio.

asked Feb 8, 2022 in Geotechnical Engineering I by Sophia (102k points)

...