A Pickering governor is driving a gramophone. Each disc attached to the centre of a leaf spring has a mass of 20 g. The width of each spring is 5 mm and thickness of 0.125 mm. The effective length of each spring is 40 mm. The distance from the spindle axis to the centre of gravity of the mass when the governor is at rest, is 10 mm, find the speed of the turntable in rpm if ratio of the governor speed to the turntable speed is 10.5.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

A Pickering governor is driving a gramophone. Each disc attached to the centre of a leaf spring has a mass of 20 g. The width of each spring is 5 mm and thickness of 0.125 mm. The effective length of each spring is 40 mm. The distance from the spindle axis to the centre of gravity of the mass when the governor is at rest, is 10 mm. Find the speed of the governor in rpm when the sleeve has risen to a height of 0.8 mm. (E = 210kN/mm^2)

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Porter governor has equal arms each of length 250 mm and pivoted on the axis of rotation. Each ball has a mass of 5 kg and the central load has a mass on the sleeve of 25 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Considering friction at the sleeve of 10N, find the range of speed in rpm.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Porter governor has equal arms each of length 250 mm and pivoted on the axis of rotation. Each ball has a mass of 5 kg and the central load has a mass on the sleeve of 25 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Considering friction at the sleeve of 10N, find the power of the governor in N-m

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Porter governor has equal arms each of length 250 mm and pivoted on the axis of rotation. Each ball has a mass of 5 kg and the central load has a mass on the sleeve of 25 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Neglecting friction at the sleeve, find the power of the governor in N-m.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Porter governor has equal arms each of length 250 mm and pivoted on the axis of rotation. Each ball has a mass of 5 kg and the central load has a mass on the sleeve of 25 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Neglecting friction at the sleeve, find the governor effort.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Porter governor has equal arms each of length 250 mm and pivoted on the axis of rotation. Each ball has a mass of 5 kg and the central load has a mass on the sleeve of 25 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Neglecting friction at the sleeve, find the sleeve lift.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Porter governor has equal arms each of length 250 mm and pivoted on the axis of rotation. Each ball has a mass of 5 kg and the central load has a mass on the sleeve of 25 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Considering friction at the sleeve of 10N, find the governor effort.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Porter governor is used to vary the speed of the turntable in a gramophone.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a porter governor, Each arm has a length of 250mm and pivoted on the axis of rotation. Sleeves carry a mass of 25kg and each ball’s mass is 5Kg. Radius of rotation: 150mm at the beginning of lift and 200mm at the maximum speed of governor. Find range in speed neglecting friction in rpm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find the equivalent length L of a simple pendulum swung about an axis.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A small connecting rod of mass 1.5 kg is suspended in a horizontal plane by two wires 1.25 m long. The wires are attached to the rod at points 120 mm on either side of the centre of gravity. If the rod makes 20 oscillations in 40 seconds, find the radius of gyration of the rod about a vertical axis through the centre of gravity.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A small connecting rod of mass 1.5 kg is suspended in a horizontal plane by two wires 1.25 m long. The wires are attached to the rod at points 120 mm on either side of the centre of gravity. If the rod makes 20 oscillations in 40 seconds, find the mass moment of inertia of the rod about a vertical axis through the centre of gravity.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin, if the angular acceleration of the rod is 23 000 rad/s^2, then find the correction couple in N-m.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a punching press, the requirement is to punch 40 mm diameter holes in a plate having a thickness of 15 mm. The rate at which the holes should be punched is 30 holes/min. Energy requirement is of 6 N-m per mm2 of sheared area. If the punching takes time 1/10 of a second and the speed of the flywheel varies from 160 to 140 rpm, determine the mass of the flywheel having radius of gyration of 1 m.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For driving a gramophone, which of the following governor is used?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. Find the mass located at gudgeon pin in Kg.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The weights move inwards and the springs bend as they rotate about the spindle axis with increasing speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A centrifugal Watt governor is fitted with two balls, each of mass 2.5 kg. Find the sped of the governor, when the balls rise by 20 mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A centrifugal Watt governor is fitted with two balls, each of mass 2.5 kg. Find the sped of the governor, when the balls fall by 20 mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin. What will be the new radius of gyration?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a governor, the sensitivity is 0.5 and the mean speed is 20 rpm, find the minimum speed.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a governor, the sensitivity is 0.5 and the mean speed is 20 rpm, find the maximum speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The crank-pin circle radius of a horizontal engine is 300 mm. The mass of the reciprocating parts is 250 kg. When the crank has travelled 30° from T.D.C., the difference between the driving and the back pressures is 0.45 N/mm^2. The connecting rod length between centres is 1.2 m and the cylinder bore is 0.5 m. If the engine runs at 250 r.p.m. and if the effect of piston rod diameter is neglected, calculate the net load on piston.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Determine the length of the chain having 200 mm pitch and is used for speed reduction from 340 rpm to 120 rpm. The numbers of teeth on driving and driven sprockets are 20 and 40 respectively. The centre to centre distance between 2 sprockets is 540 mm and diameter of driven sprocket is 450 mm.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A uniform disc of diameter 300 mm and of mass 5 kg is mounted on one end of an arm of length 600 mm. The other end of the arm is free to rotate in a universal bearing. If the disc rotates about the arm with a speed of 300 r.p.m. clockwise, looking from the front, with what speed will it precess about the vertical axis?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

...