At an engine throttle position of 75% the high idle speed of engine is shifted by 200 rpm towards maximum torque position. If the engine is maintaining a uniform speed of 2475 rps at given load, governor regulation is _____

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The high idle speed of engine is 2240 rpm. The peak torque of 180 Nm occurs, at 1450 engine rpm. If the lugging ability is 28 Nm. The engine power in KW at governor’s maximum position will be _________ (Governor regulation = 11.5%)

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

The average speed of engine connected to governor is 1500 rpm. If the fluctuation in speed is +-100 rpm, then % governor regulation is ______

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A Proell governor has equal arms of length 300 mm. The upper and lower ends of the arms are pivoted on the axis of the governor. The extension arms of the lower links are each 80 mm long and parallel to the axis when the radii of rotation of the balls are 150 mm and 200 mm. The mass of each ball is 10 kg and the mass of the central load is 100 kg. Determine the range of speed of the governor.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Varying the governor setting in an IC engine

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Which governor is known as sensitive governor?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Which governor does not achieve ISOCHRONOUS behaviour?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

Who theoretically analysed James Watt’s design as a mathematical energy balance purpose?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

What is the regulation of speed when speed at no load of engine is 1973 rpm and speed at load is 1873 rpm?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

While testing a wheat thresher at recommended throughout 80 Nm torque is recorded at 850 rpm at the main shaft of the threshing cylinder, which is operated by a 200-mm diameter pulley. The overload factor and unit mass of V-belt are 1.2 and 0.9 kg/m respectively. At condition of maximum power transfer the maximum tension in V-belt in N is __________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

While testing a wheat thresher at recommended throughout, 80 Nm torque is recorded at 750 rpm at the main shaft of the threshing cylinder, which is operated by a 200-mm diameter V pulley. The overload factor and unit mass of V-belt are 1.2 and 0.9 kg/m respectively. At condition of maximum power transfer the maximum tension in V-belt in N is ________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

The speed reduction in 1^st low gear of tractor box and differential with final drive are 5:1 and 45:1 for a tractor developing 30 KW at engine at an rpm of 2500 with overall efficiency of 85%. The torque is KN-m available at wheel axle?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A Porter governor has equal arms each of length 250 mm and pivoted on the axis of rotation. Each ball has a mass of 5 kg and the central load has a mass on the sleeve of 25 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Considering friction at the sleeve of 10N, find the range of speed in rpm.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+2 votes

1 answer

In an epicyclic gear train, an arm carries two wheels ‘A’ and ‘B’ having 24 teeth and 30 teeth respectively. If the arm rotates at 100 rpm in the clockwise direction about the centre of the wheel. ‘A’ which is fixed, then the speed of wheel on its own axis is _____

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

The pitch of a chain is 200 mm. An 8 sprocket is operating at 250 rpm and driving a 25 teeth sprocket through the drain. The tension in the chain is 15 KN. Determine the maximum power.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Find the gear ratio of a tractor of its final drive of tractor has 1.2 m tractor wheel and forward speed of 5km/h. When engine is running at 1000 rpm if reduction in transmission is 3:1

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A two-wheel drive tractor is pulling a load of 12 KN horizontally on levelled surface at forward speed of 5km/hr. The rolling radius of traction wheel and wheel slip are 0.65m and 20% respectively. If rear axle torque is 9KNm the tractive efficiency is ______

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A four-stroke diesel engine operating at 1200 rpm uses 0.1 kg of fuel in 5 minutes and develops a torque of 7.5 kg-m. What is the brake specific fuel consumption.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A hydraulic circuit uses 25 litres of fluid per min. The fluid is supplied by a pump having a fixed displacement of 12.5 cm^3 per revolution driven at 3000 rpm. The pump has a volumetric efficiency of 0.85 and torque efficiency of 0.88. If the system pressure is set at 18 MPa by the relief valve. What will be the power required to drive the pump?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A four-stroke diesel engine operating at 800 rpm uses 0.10 kg of fuel in 4 minutes while developing a torque of 70 Nm. Calculate brake specific fuel consumption

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A four-stroke diesel engine operating at 1200 rpm uses 0.1 kg of fuel in 5 minutes and has the brake specific fuel consumption equals to 0.1910 kg\BHP\h. Calculate the torque developed.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A 10 teeth sprocket is operating at 200 rpm and driving a 25 teeth sprocket through a chain. The pitch of the chain is 20 mm and ultimate strength is 20 KN. Calculate the average linear speed.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A single plate clutch with both sides effective, has an outer diameter of 30 cm and inner diameter of 20 cm. the maximum intensity of pressure at any point in the contact surface is not exceed 1 kg/cm^2. If the co-efficient of friction is 0.3, determine the horse power transmitted by a clutch speed of 2000 rev/min.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

An I.C. engine consumes high speed diesel oil at the rate of 0.5 kg/h. What is the power of the engine?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

An IC engine consumes high speed diesel oil at the rate of 0.5 kg/h. Calculate the power of the engine.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A 20 teeth sprocket is operating at 150 rpm and driving a 43 teeth sprocket through a chain. The pitch of the chain is 250 mm and alternate strength is 10 KN. Determine the average torque applied to driven shaft at maximum power transmission.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

...