The pitch of a chain is 200 mm. An 8 sprocket is operating at 250 rpm and driving a 25 teeth sprocket through the drain. The tension in the chain is 15 KN. Determine the maximum power.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

A 20 teeth sprocket is operating at 150 rpm and driving a 43 teeth sprocket through a chain. The pitch of the chain is 250 mm and alternate strength is 10 KN. Determine the average torque applied to driven shaft at maximum power transmission.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A 10 teeth sprocket is operating at 200 rpm and driving a 25 teeth sprocket through a chain. The pitch of the chain is 20 mm and ultimate strength is 20 KN. Calculate the average linear speed.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Determine the length of the chain having 200 mm pitch and is used for speed reduction from 340 rpm to 120 rpm. The numbers of teeth on driving and driven sprockets are 20 and 40 respectively. The centre to centre distance between 2 sprockets is 540 mm and diameter of driven sprocket is 450 mm.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A chain is used for speed reduction from 240 rpm to 110 rpm. The number of teeth on driving sprocket is 22. The centre to centre distance between 2 sprockets is 540 mm and pitch circle diameter of driven sprockets is 480 mm. determine number of teeth on driven sprockets.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

The chain drive is used to reduce the speed from 180 rpm to 90 rpm, the driving sprocket has 20 teeth and pitch circle diameter of 500 mm. The centre to centre distance between the sprockets of chain drive is 550 mm. Determine total number of links.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

The centre to centre distance between two sprockets of chain drives is 600 mm. The chain drive is used to reduce the speed from 160 rpm to 90 rpm. The driving sprocket has 18 teeth and pitch circle diameter of 480 mm. Determine the pitch of the chain and teeth on driven sprocket.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

The number of teeth in driving spur gear is 60. The circular pitch of the teeth is 15 mm. the tangential force transmitted is 140 kg. Calculate horsepower transmitted to the driven gear at 180 rpm of driving gear.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

While testing a wheat thresher at recommended throughout 80 Nm torque is recorded at 850 rpm at the main shaft of the threshing cylinder, which is operated by a 200-mm diameter pulley. The overload factor and unit mass of V-belt are 1.2 and 0.9 kg/m respectively. At condition of maximum power transfer the maximum tension in V-belt in N is __________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Calculate the power transmitted by the belt and pulley arrangement, if tension on tight side of the belt is 50 kg and tension on slack side is 25 kg. The diameter and speed of driving pulley is 0.95 m and 350 rpm.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

In a single V-belt drive having 30° groove angle, the cross-section area of belt is 350 mm^2 and mass density of belt material is 1400 kg/m^3. The maximum tension transmitted through the belt in kN is ________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

In an epicyclic gear train, one arm carries two wheels A and B having 25 teeth and 35 teeth respectively. If the arm rotates at 100 rpm in clockwise direction about centre of wheel A which is fixed, then speed of wheel on its own axis will be?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

While testing a wheat thresher at recommended throughout, 80 Nm torque is recorded at 750 rpm at the main shaft of the threshing cylinder, which is operated by a 200-mm diameter V pulley. The overload factor and unit mass of V-belt are 1.2 and 0.9 kg/m respectively. At condition of maximum power transfer the maximum tension in V-belt in N is ________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

In a tractor differential, the pinion on the propeller shaft has 12 teeth and the crown gear has 50 teeth. The propeller shaft rotates at 1500 rpm and the right rear axle rotates at 250 rpm while taking a left turn. The rotation of the left axle in rpm will be __________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A single reduction gear of 120 KW with a pinion of 150 mm pitch circle diameter and speed 550 rpm is supported in bearings on either side. Calculate the total load due to power transmission.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

In a belt drive, the mass of the belt is 10 kg/m and its speed is 6 m/s. The drive transmits 20 KW of power. Determine the initial tension in the belt and the strength of the belt. The co-efficient of friction is 0.25 and wrap angle is 220°.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

The width of belt is 15 cm and maximum tension per cm width is not to exceed 12 kg. T1/T2=2.25. Diameter of driver=1m and it makes 220 rpm. Find the horse power that can be transmitted.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

In an epicyclic gear train, the sun gear on the input shaft is 20 teeth external gear. The planet gear is a 40 teeth external gear and the ring gear is a 100 teeth internal gear. The ring gear is fixed and the sun gear is rotating at 60 rpm counter clockwise. The arm attached to output shaft will rotate at ________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

The speed reduction in 1^st low gear of tractor box and differential with final drive are 5:1 and 45:1 for a tractor developing 30 KW at engine at an rpm of 2500 with overall efficiency of 85%. The torque is KN-m available at wheel axle?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

If a driven pulley is made at 350 rpm by a driving pulley of 0.3 m diameter running at 1400 rpm. Determine length of open belt when the pulleys are 4 meters apart.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Chain and sprocket drive is preferred, when two parallel shafts are placed at a distance of _______

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

What power is transmitted by belt and pulley arrangement, if tension on tight side of belt is 60 kg and tension on slack side is 25kg. The diameter and speed of driving pulley is 0.95 m and 250 rpm respectively.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

The diameter of feed roller of a conveyor type power chaff cutter is 100mm and they are rotating at 100 rpm for cutting the dry fodder. The effective length of each feed roller is 0.25 m and average clearance between them is 0.015 mm. The compression density while passing through feed roller is 350 kg/m^3. What will be the capacity of chaff cutter?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Determine the length of cross belt of connecting two pulleys 5 cm apart. The diameter of driving and driven pulleys are 1.25 m and 0.75 m respectively.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A V-belt is used to transmit 5 KW at 17 m/s, the included angle of the belt is 38°, the density of the belt is 1.25 g/cm^3, contact angle on smaller pulley is 150°, tension on the belt is adjusted by providing idlers. Find tension at tight and slack side of belt.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A Porter governor has equal arms each of length 250 mm and pivoted on the axis of rotation. Each ball has a mass of 5 kg and the central load has a mass on the sleeve of 25 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Considering friction at the sleeve of 10N, find the range of speed in rpm.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

...