In a single V-belt drive having 30° groove angle, the cross-section area of belt is 350 mm^2 and mass density of belt material is 1400 kg/m^3. The maximum tension transmitted through the belt in kN is ________

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

While testing a wheat thresher at recommended throughout 80 Nm torque is recorded at 850 rpm at the main shaft of the threshing cylinder, which is operated by a 200-mm diameter pulley. The overload factor and unit mass of V-belt are 1.2 and 0.9 kg/m respectively. At condition of maximum power transfer the maximum tension in V-belt in N is __________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

In a belt drive, the mass of the belt is 10 kg/m and its speed is 6 m/s. The drive transmits 20 KW of power. Determine the initial tension in the belt and the strength of the belt. The co-efficient of friction is 0.25 and wrap angle is 220°.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A V-belt is used to transmit 5 KW at 17 m/s, the included angle of the belt is 38°, the density of the belt is 1.25 g/cm^3, contact angle on smaller pulley is 150°, tension on the belt is adjusted by providing idlers. Find tension at tight and slack side of belt.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Calculate the power transmitted by the belt and pulley arrangement, if tension on tight side of the belt is 50 kg and tension on slack side is 25 kg. The diameter and speed of driving pulley is 0.95 m and 350 rpm.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

While testing a wheat thresher at recommended throughout, 80 Nm torque is recorded at 750 rpm at the main shaft of the threshing cylinder, which is operated by a 200-mm diameter V pulley. The overload factor and unit mass of V-belt are 1.2 and 0.9 kg/m respectively. At condition of maximum power transfer the maximum tension in V-belt in N is ________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

If a driven pulley is made at 350 rpm by a driving pulley of 0.3 m diameter running at 1400 rpm. Determine length of open belt when the pulleys are 4 meters apart.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A V-belt operates at 25 m/s peripheral speed. The mass of the belt per unit length is 0.9 kg/m. The value of centrifugal tension in belt is ______

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

The pitch of a chain is 200 mm. An 8 sprocket is operating at 250 rpm and driving a 25 teeth sprocket through the drain. The tension in the chain is 15 KN. Determine the maximum power.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

If a driven pulley is made to rotate at 350 rpm by a driving pulley of 0.3 m diameter, running at 1400 rpm, what will be the length of open belt drive when the pulleys are 2 m apart?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

In case of V-belt the groove angle in small pullies is about _________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

The diameter of feed roller of a conveyor type power chaff cutter is 100mm and they are rotating at 100 rpm for cutting the dry fodder. The effective length of each feed roller is 0.25 m and average clearance between them is 0.015 mm. The compression density while passing through feed roller is 350 kg/m^3. What will be the capacity of chaff cutter?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A leather belt 100 mm wide and 10 mm thick with a safe permissible stress of 1.5 MPa is used for transmitting a maximum power of 15 KW. If the density of belt material is 1 g/cm^3, the velocity of belt for maximum power transmission will be ________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A 20 teeth sprocket is operating at 150 rpm and driving a 43 teeth sprocket through a chain. The pitch of the chain is 250 mm and alternate strength is 10 KN. Determine the average torque applied to driven shaft at maximum power transmission.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

In a belt drive the mass of the belt is 1 kg/m and its speed is 6m/s. The drive transmits 9.6 KW of power. Determine the strength of the belt when the coefficient of friction is 0.25 and wrap angle is 220°.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

The width of belt is 15 cm and maximum tension per cm width is not to exceed 12 kg. T1/T2=2.25. Diameter of driver=1m and it makes 220 rpm. Find the horse power that can be transmitted.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A single plate clutch with both sides effective, has an outer diameter of 30 cm and inner diameter of 20 cm. the maximum intensity of pressure at any point in the contact surface is not exceed 1 kg/cm^2. If the co-efficient of friction is 0.3, determine the horse power transmitted by a clutch speed of 2000 rev/min.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

The speed reduction in 1^st low gear of tractor box and differential with final drive are 5:1 and 45:1 for a tractor developing 30 KW at engine at an rpm of 2500 with overall efficiency of 85%. The torque is KN-m available at wheel axle?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A V-belt operates at 23.56 m/s peripheral speed. The mass of the belt per unit length is 0.9 kg/m. The value of centrifugal tension is _______

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A countershaft of engineering workshop is driven by electric motor with the help of canvas belt and pulley arrangement such that the speed of bet is 600 m/min and it transmits 50 KW. Find the difference between tension on either side of the belt.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A 10 teeth sprocket is operating at 200 rpm and driving a 25 teeth sprocket through a chain. The pitch of the chain is 20 mm and ultimate strength is 20 KN. Calculate the average linear speed.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

The number of teeth in driving spur gear is 60. The circular pitch of the teeth is 15 mm. the tangential force transmitted is 140 kg. Calculate horsepower transmitted to the driven gear at 180 rpm of driving gear.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Determine the length of cross belt of connecting two pulleys 5 cm apart. The diameter of driving and driven pulleys are 1.25 m and 0.75 m respectively.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A single cylinder oil engine works with a three rotor system, the shaft length is 2.5m and 70mm in diameter, the middle rotor is at a distance 1.5m from one end. Calculate the free torsional vibration frequency for a two node system in Hz if the mass moment of inertia of rotors in Kg-m^2 are: 0.15, 0.3 and 0.09. C=84 kN/mm^2

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A single cylinder oil engine works with a three rotor system, the shaft length is 2.5m and 70mm in diameter, the middle rotor is at a distance 1.5m from one end. Calculate the free torsional vibration frequency for a single node system in Hz if the mass moment of inertia of rotors in Kg-m^2 are: 0.15, 0.3 and 0.09. C=84 kN/mm^2

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

What is the width of belt to transmit 15 HP to a pulley 35 cm in diameter. Pulley makes 1600 rev/min, coefficient of friction between belt is 0.22 and angle of contact is 20°. Maximum tension in belt not to exceed 8 kg per cm width.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

...