A hydraulic sprayer fitted with hollow cone nozzle is required to be calibrated for application rate 150 l/ha. The sprayer speed is 6.5/h, nozzle spacing is 50 cm, and the available 0.787 mm orifice diameter nozzle is rated at 0.473 l/min. What will be the nozzle flow rate?

Question

A hydraulic sprayer fitted with hollow cone nozzle is required to be calibrated for application rate 150 l/ha. The sprayer speed is 6.5/h, nozzle spacing is 50 cm, and the available 0.787 mm orifice diameter nozzle is rated at 0.473 l/min. What will be the nozzle flow rate?

1 Answer

Related questions

+2 votes

1 answer

A hydraulic sprayer fitted with hollow nozzle is required to be calibrated for application rate 150 L/ha. The sprayer speed is 6.5 km/h. Nozzle spacing is 50 cm. The available 0.787 mm orifice diameter. Nozzle is rated at 0.473 L/min. What is the nozzle flow rate?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A tractor sprayer is fitted with 20 hollow cones nozzles to attain application rate of 200 l/hr. During the calibration test, the nozzle flow rate was found to be 1.25 l/min whereas, the rated nozzle flow rate was found to be 0.473 l/min was available at 275 kPa. If the nozzle produces droplets with volume median diameter 200 μm at 1 Mg Pascal, the droplet at the desire flow rate is?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A field sprayer having a horizontal boom with 20 nozzles spaced 40 cm apart is to be designed for maximum application rate of 650 l/ha at nozzle pressure of kPa and forward speed of km/h. What will be the pump capacity in l/min?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A sprayer having 0.4 L/min nozzle discharge rate and 50 cm width of coverage is required to apply 0.8 kg of active ingredient per hectare. If 1 kg of active ingredient is content in 120 L of spray solution. What will be the speed of travel of sprayer?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

An air blast of sprayer is to be operated at 3 km/h and application rate is 18 l/tree. The spacing is 9m*9m and each nozzle delivers 5 lit/min and operating process of 4*10^5 N/m^2. If one half row is sprayed from each side of the machine. How many sprayers will be needed?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

An air blast of sprayers is to be operated at 3 km/hour and desired application rate is 18 l/tree. The tree spacing is 9*9 m and nozzle delivers 5 l/min at operating pressure of 4*10^5 N/m^2. How many nozzles would be needed?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A sprayer having 0.4 litre per minute nozzle discharge rate and 50 cm width of coverage, is required to apply 0.8 kg of active ingredient per hectare. If one kg of active ingredient is contained in 120 litres of spray solution, determine the speed of the sprayer.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A 4*100 cm seed drill is to be operated at a forward speed of 3.6 km/h. The diameter of the ground wheel is 50 cm. a cup type metering mechanism with 10 cells on its periphery is used for dropping one seed in a hill. Power transmitted from the ground wheel shaft to the metering shaft with the help of chain and sprocket arrangement. If the desired plant population is 6000 per hectare and average emergence is 75% speed ratio between ground wheel shaft and metering shaft will be ____________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

During a test, discharge measured through a hydraulic spray nozzle was 45010^-6 m^3/min at nozzle operating pressure of 284 kPa. If the pressure is increased by 10%, the percent increase in discharge will be ________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A flat blade turbine having six blades is centrally installed in a vertical tank. The tank is 6 ft (1.83 m) in diameter; the turbine is 2 ft. (0.61 m) in diameter and is positioned 2 ft (0.61 m) from the bottom of the tank. The turbine blades are 5 in. (127 mm) wide. The tank is filled to a depth of 6 ft (1.83 m) with a solution of 50 percent caustic soda, at 150°F (65.6°C), which has a viscosity of 12 cP and a density of 93.5 lb/ft^3 (1498 kg/m^3). The turbine is operated at 90 r/min. the tank is baffled. What power will be required to operate the mixer? (Given KL=403680).

asked Feb 2, 2022 in Food Processing Unit Operations by Ava (110k points)

+1 vote

1 answer

What will be the water power which is required to discharge liquid at the rate of 30 litres/min at 30 kg/cm^2 pressure?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A cylinder type chaff cutter head in a direct throw field chopper has 5 knives and diameter as 450 mm. The throat size is 40*12 cm for 15 mm theoretical length of cut with corn silage. What will be the rated capacity in megagrams per hours at 100% field efficiency?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A hydraulic circuit uses 25 litres of fluid per min. The fluid is supplied by a pump having a fixed displacement of 12.5 cm^3 per revolution driven at 3000 rpm. The pump has a volumetric efficiency of 0.85 and torque efficiency of 0.88. If the system pressure is set at 18 MPa by the relief valve. What will be the power required to drive the pump?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A field chaff cutter with cutter head has 4 knives and diameter of 650 mm. The given peripheral speed is 30 m/s and throat size is 45*15 cm. For 20 mm length of cut with corn silage what will be the linear speed and rated feeding capacity?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A 4-row animal drawn wheat seed drill with 300 mm row-to-row spacing is operated at 1.5 km/h. If the time loss, based on observed total time in seeding 1 ha arc is 15% in turning, 10% in seed filling and 10% in mechanical down time, then what is the field efficiency?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

Find the suction capacity of a power sprayer if diameter is 25 m, speed is 1100 rev/min length of stroke is 22 mm, number of plunger is 3.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

During a discharge measured through a hydraulic spray nozzle was 450*10^-6m^3/min at nozzle operating pressure of 284 kPa. If the pressure is increased by 10%. The percent increase in discharge will be _______

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

What will be the diameter of base of a spray cone in a boom sprayer?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A three-tine cultivator having tine spacing 6 cm, working depth of 3 cm and speed is 2 km/hr. Turning loss is 10%. Soil resistance is 0.6 kg/cm^2. Width of furrow is 6 cm. What will be the required power?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A five-tine cultivator having tine spacing 8cm, working depth of 5cm and speed is 3km/hr. Turning loss is 10%. Soil resistance is 0.6 kg/cm^2. Width of furrow is 5 cm. What will be the maximum draft?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A side dressing fertilizer applicator is to plough two bands per row on a crop with 1 m row spacing at an application rate of 600 kg/hour. If the machine is calibrated by driving it forward over a distance of 50 m, the mass of material collected from each delivery tube is _________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Two pulleys are connected by a belt. The sum of the diameters of the pulleys is 92.6 cm and while one makes 50 rev/min the other make 200 rev/min. What will be the diameter of the pulleys?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A seed drill has 8 cells on cup feed metering mechanism. The rolling of ground wheel to that of the roller is 2:3. If drilling is done at a forward speed of 3.5 km/h, spacing in the rows in mm will be ___________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A traction wheel having 600 mm diameter was tested in a soil bin and following data was obtained, angular speed=10rpm, input torque to wheel angle=60 Nm, drawbar pull=150 N, normal load on wheel axle=500 N, wheel forward speed=0.25 ms^-1. What will be the tractive efficiency?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A traction wheel having 600 mm diameter was tested in a soil bin and following data was obtained, angular speed=10rpm, input torque to wheel angle=60 Nm, drawbar pull=150 N, normal load on wheel axle=500 N, wheel forward speed=0.25 ms^-1. What will be the slippage?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

A hydraulic sprayer fitted with hollow cone nozzle is required to be calibrated for application rate 150 l/ha. The sprayer speed is 6.5/h, nozzle spacing is 50 cm, and the available 0.787 mm orifice diameter nozzle is rated at 0.473 l/min. What will be the nozzle flow rate?

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories