Wire rope specified as 8×10. Calculate the number of strands.

Question

Wire rope specified as 8×10. Calculate the number of strands.

← Prev Question Next Question →

1 Answer

Related questions

0 votes

0 answers

Does oil seal consist of any spring in its structure?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

An oil seal is a mechanical device made of elastic material which is used to prevent leakage of fluid between two machine components.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Class 1 pressure vessels are used to contain

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

An unfired pressure vessel is used to carry stem, gases or fluids at pressure

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If magnitude of contact pressure between sealing lip and rotating shaft is very high then

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which type of rope drum is preferred?

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In design of wire ropes, bending stress is converted into an equivalent bending load which is given by [d= diameter of individual wire and D= diameter of sheave].

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Piston rod is an example of column.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Slenderness ratio is [l= length of column and k= least radius of gyration of cross section about its axis].

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Bucking of column means

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Short column and long column are classified on the basis of

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Columns with what slenderness ratio are not designed with respect to buckling but are designed for compressive stresses.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Steel columns with a slenderness ratio of 95 are

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following are true for End fixity coefficient

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If slenderness ratio=45, which mode of failure will dominate?

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the tension in the rope of pulley C.

asked Jan 21 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If centre distance for a chain drive is 750mm with number of teeth on the driving and driven sprockets being 40 and 20 respectively, then calculate the number of links required. Given: Pitch is taken as 19mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm².

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m.

asked Jan 21 in Machine Design by Chris (52.6k points)

0 votes

0 answers

A rolling contact bearing is specified as X307. Determine the series.

asked 1 day ago in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A rivet is specified as a 20mm rivet. What does it mean?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If maximum tension in the belt is 900N and allowable belt load is 500N. Calculate the number of belts required to transmit power.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

What would be the percent increase in length of wire of diameter 2.5 x I0^-3m stretched by a force of 980 N. Young’s modulus of elasticity of wire is 8 x 10^10 N/m^2.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

0 votes

0 answers

Belt, chain and rope are called rigid drives.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

______ is used for a shaft that supports rotating elements like wheels, drums or rope sleaves.

asked Jan 23 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-02-02T14:40:54+0000

The suitable answer is (a) 8

Dive into clarity with: First number indicates number of strands.

Wire rope specified as 8×10. Calculate the number of strands.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories