Which among these devices are the best suited for the measurement of high pressure liquids with high accuracy?

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

What type of liquids are measured using a manometer?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

The pressure at any given point of a non-moving fluid is called the ____________

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

What is the pressure in Pascals at a depth of 1m below the water surface?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The device used to measure the fluid pressure is _____________

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

15 bar equals to __________ Pascals.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

How do we measure the flow rate of liquid? (a)Coriolis method

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A tank of height 3 m is completely filled with water. Now two-third of the liquid is taken out and an equal amount of two other immiscible liquids of specific gravities 0.8 and 1.2 are poured into the tank. By what percent will the pressure at the base of the tank change?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A beaker of height 15 cm is completely filled with water. Now two-third of the liquid is taken out and an equal amount of two other immiscible liquids of specific gravities 0.8 and 1.2 are poured into the tank. What will be the pressure (in kPa) at a point situated at a height, half the height of the beaker?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Manometers are the pressure measuring devices which use the principle of dynamic pressure to measure the pressure difference.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

For dynamic fluid motion in a pipe, the pressure measurement cannot be carried out accurately by manometer.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A beaker half-filled with water is exposed to the atmosphere. If the pressure at points A, B and C as shown are Pa, Pb and Pc respectively, which one of the following will be the relation connecting the three?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

Three beakers 1, 2 and 3 of different shapes are kept on a horizontal table and filled with water up to a height h. If the pressure at the base of the beakers are P1, P2 and P3 respectively, which one of the following will be the relation connecting the three?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

0 answers

A beaker is filled with a liquid up to a height h. If A and B are two points, one on the free surface and one at the base as shown, such that the minimum distance between the two is l, what will be the pressure at point B?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

Calculate the hydrostatic pressure for water moving with constant velocity at a depth of 5 m from the surface.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A simple U tube manometer connected to a pipe in which liquid is flowing with uniform speed will give which kind of pressure?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A closed tank (each side of 5 m) is partially filled with fluid as shown. If the pressure of the air above the fluid is 2 bar, find the pressure at the bottom of the tank. Assume the density ρ of the fluid to vary according to the given relation:

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A beaker of height 10 cm is half-filled with water (Sw = 1) and half-filled with oil (So = 1). At what distance (in cm) from the base will the pressure be half the pressure at the base of the beaker?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

0 answers

A beaker is filled with a liquid of density ρ1 up to a certain height. A is a point, h m downwards from the free surface such that the pressure at A is P. If the liquid is replaced by equal volume of another liquid of density ρ2, at what distance from the free surface will the pressure be P now?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A cuboidal container (each side of 30 cm0) is completely filled with water. A is a point, 25 cm above the base such that the pressure at point A is P. At what height (in cm) from the base will the pressure be 2P?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A beaker, partially filled with a liquid is rotated by an angle 30^o as shown. If the pressure at point B becomes 12 bar, what will be the height (in cm) of the beaker?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A beaker of height 30 cm is filled with water (Sw = 1) up to a height of 10 cm. Now oil (So = 0:9) is poured into the beaker till it is completely filled. At what distance (in cm) from the base will the pressure be one-third the pressure at the base of the beaker?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A beaker of height h is filled with a liquid of density ρ up to a certain limit. The beaker is rotated by an angle θ such that further increase in the angle will result in over flow of the liquid. If the liquid surface is exposed to the atmosphere, what will be the gauge pressure at point B?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A beaker is filled with a liquid of specific gravity S = 1:2 as shown. What will be the pressure difference (in kN/m^2) between the two points A and B, 30 cm below and 10 cm to the right of point A?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A beaker is filled with a liquid of density ρ1 up to a certain height. A is a point, h m downwards from the free surface of the liquid as shown. The liquid is replaced by equal volume of another liquid of density ρ2. If ρ1 > ρ2, how will the pressure at point A change?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

Differential manometer gives the pressure reading with respect to atmospheric pressure.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

...