What will be the water power which is required to discharge liquid at the rate of 30 litres/min at 30 kg/cm^2 pressure?

Question

What will be the water power which is required to discharge liquid at the rate of 30 litres/min at 30 kg/cm^2 pressure?

1 Answer

Related questions

+1 vote

1 answer

A sprayer having 0.4 L/min nozzle discharge rate and 50 cm width of coverage is required to apply 0.8 kg of active ingredient per hectare. If 1 kg of active ingredient is content in 120 L of spray solution. What will be the speed of travel of sprayer?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

In a pump, suction volume is 25 litres/min and the pump efficiency is 85%. Calculate the shaft power at a pressure of 35kg/cm^2

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A sprayer having 0.4 litre per minute nozzle discharge rate and 50 cm width of coverage, is required to apply 0.8 kg of active ingredient per hectare. If one kg of active ingredient is contained in 120 litres of spray solution, determine the speed of the sprayer.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A hydraulic sprayer fitted with hollow cone nozzle is required to be calibrated for application rate 150 l/ha. The sprayer speed is 6.5/h, nozzle spacing is 50 cm, and the available 0.787 mm orifice diameter nozzle is rated at 0.473 l/min. What will be the nozzle flow rate?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A field sprayer having a horizontal boom with 20 nozzles spaced 40 cm apart is to be designed for maximum application rate of 650 l/ha at nozzle pressure of kPa and forward speed of km/h. What will be the pump capacity in l/min?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A hydraulic circuit uses 25 litres of fluid per min. The fluid is supplied by a pump having a fixed displacement of 12.5 cm^3 per revolution driven at 3000 rpm. The pump has a volumetric efficiency of 0.85 and torque efficiency of 0.88. If the system pressure is set at 18 MPa by the relief valve. What will be the power required to drive the pump?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A hydraulic sprayer fitted with hollow nozzle is required to be calibrated for application rate 150 L/ha. The sprayer speed is 6.5 km/h. Nozzle spacing is 50 cm. The available 0.787 mm orifice diameter. Nozzle is rated at 0.473 L/min. What is the nozzle flow rate?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A single plate clutch with both sides effective, has an outer diameter of 30 cm and inner diameter of 20 cm. the maximum intensity of pressure at any point in the contact surface is not exceed 1 kg/cm^2. If the co-efficient of friction is 0.3, determine the horse power transmitted by a clutch speed of 2000 rev/min.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

An air blast of sprayer is to be operated at 3 km/h and application rate is 18 l/tree. The spacing is 9m*9m and each nozzle delivers 5 lit/min and operating process of 4*10^5 N/m^2. If one half row is sprayed from each side of the machine. How many sprayers will be needed?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

An air blast of sprayers is to be operated at 3 km/hour and desired application rate is 18 l/tree. The tree spacing is 9*9 m and nozzle delivers 5 l/min at operating pressure of 4*10^5 N/m^2. How many nozzles would be needed?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

During a discharge measured through a hydraulic spray nozzle was 450*10^-6m^3/min at nozzle operating pressure of 284 kPa. If the pressure is increased by 10%. The percent increase in discharge will be _______

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

During a test, discharge measured through a hydraulic spray nozzle was 45010^-6 m^3/min at nozzle operating pressure of 284 kPa. If the pressure is increased by 10%, the percent increase in discharge will be ________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A tractor sprayer is fitted with 20 hollow cones nozzles to attain application rate of 200 l/hr. During the calibration test, the nozzle flow rate was found to be 1.25 l/min whereas, the rated nozzle flow rate was found to be 0.473 l/min was available at 275 kPa. If the nozzle produces droplets with volume median diameter 200 μm at 1 Mg Pascal, the droplet at the desire flow rate is?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A three-tine cultivator having tine spacing 6 cm, working depth of 3 cm and speed is 2 km/hr. Turning loss is 10%. Soil resistance is 0.6 kg/cm^2. Width of furrow is 6 cm. What will be the required power?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A diesel tractor consumes 5 litres per hour of fuel whose density is 0.836 kg per litre. The heating value of the fuel is 45.4 MJkg^-1. If the thermal efficiency of the engine is 0.30, the transmission efficiency is 0.90 and the tractive efficiency is 0.75, the drawbar power of the tractor will be __________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

What is the pressure at which Power sprayers are operated?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

What will be the torque required to drive a 0.1 litre/min pump at 2000 rpm of delta pressure across pump is 240 bars?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A flat blade turbine having six blades is centrally installed in a vertical tank. The tank is 6 ft (1.83 m) in diameter; the turbine is 2 ft. (0.61 m) in diameter and is positioned 2 ft (0.61 m) from the bottom of the tank. The turbine blades are 5 in. (127 mm) wide. The tank is filled to a depth of 6 ft (1.83 m) with a solution of 50 percent caustic soda, at 150°F (65.6°C), which has a viscosity of 12 cP and a density of 93.5 lb/ft^3 (1498 kg/m^3). The turbine is operated at 90 r/min. the tank is baffled. What power will be required to operate the mixer? (Given KL=403680).

asked Feb 2, 2022 in Food Processing Unit Operations by Ava (110k points)

+1 vote

1 answer

What will be the temperature, at which 28g nitrogen occupies a volume of 10 litres at 2.46 atmospheric pressure?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A power operated chaff cutter is used for cutting Napier grass of density 640 kg/m^3 at 800 rpm speed. If blades make a clearance angle of 18° between the knife support assembly and the plan of rotation and distance of inner edge of throat from flywheel centre is 10 cm. What will be the theoretical length of cut without feed interference using 4 knives?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A four bottom 40 cm MB plough has a working depth of 15 cm and draft of 1600 kg. It is working at a speed of 15 cm and draft of 1600 kg. it is working at a speed of 4.5 km/hr with field efficiency of 70%. What will be the drawbar power?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Which part of power sprayer is used to break the liquid into desired spray and deliver to plants?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

Find the suction capacity of a power sprayer if diameter is 25 m, speed is 1100 rev/min length of stroke is 22 mm, number of plunger is 3.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A simple band brake has the tight side of the band attached to a fixed pivot. The angle of wrap is 280° about a 450-mm diameter drum. A torque of 170 mm is sustained at 900 revs min^-1. If the co-efficient of friction is 0.2 the required belt tension at tight side of the belt will be _____

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

What power is required to pull 1.2 mete mower working at a speed of 4.8 km/hr, if there is a load of 50 kg per metre length of mower and mechanical efficiency is 80%?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

What will be the water power which is required to discharge liquid at the rate of 30 litres/min at 30 kg/cm^2 pressure?

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories