Steel columns with a slenderness ratio of 95 are

Question

Steel columns with a slenderness ratio of 95 are

1 Answer

Related questions

+1 vote

1 answer

Columns with what slenderness ratio are not designed with respect to buckling but are designed for compressive stresses.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Slenderness ratio is [l= length of column and k= least radius of gyration of cross section about its axis].

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If slenderness ratio=45, which mode of failure will dominate?

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Short column and long column are classified on the basis of

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following are true for End fixity coefficient

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Piston rod is an example of column.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Bucking of column means

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Class 1 pressure vessels are used to contain

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

An oil seal is a mechanical device made of elastic material which is used to prevent leakage of fluid between two machine components.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Does oil seal consist of any spring in its structure?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which type of rope drum is preferred?

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Wire rope specified as 8×10. Calculate the number of strands.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

An unfired pressure vessel is used to carry stem, gases or fluids at pressure

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If magnitude of contact pressure between sealing lip and rotating shaft is very high then

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In design of wire ropes, bending stress is converted into an equivalent bending load which is given by [d= diameter of individual wire and D= diameter of sheave].

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the interference [E=210kN/mm²].

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stresses due to shrink shift in jacket.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the tangential stress in compound cylinder.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stress due to shrink shift in inner tube.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the radial stress in compound cylinder.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the shrinkage pressure.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Poor fluidity and contraction are compulsory to be taken into consideration while designing a cast steel product.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the ratio factor Q if a pair of bevel gear consist of 25 teeth pinion meshing with a 40 teeth gear.

asked Feb 2 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-01-27T10:35:19+0000

Accurate option is (a) Short Columns

Navigate through clarity with: Steel columns with slenderness ratio <100 are classified in short columns.

Steel columns with a slenderness ratio of 95 are

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories