The driving and driven shafts connected by a Hooke’s joint will have equal speeds, if

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the maximum speed of the intermediate shaft if the driving shaft has a constant speed of 500 r.p.m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the maximum speed of the driven shaft if the driving shaft has a constant speed of 500 r.p.m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the minimum speed of the driven shaft if the driving shaft has a constant speed of 500 r.p.m.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the minimum speed of the intermediate shaft if the driving shaft has a constant speed of 500 r.p.m.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts having an included angle of 150° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Using the above data, calculate the maximum angular acceleration of the driven shaft in rad/s^2.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts having an included angle of 150° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Using the above data, calculate the maximum torque required in N-m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts with an included angle of 160° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Find the maximum angular acceleration of the driven shaft.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A Hooke’s joint is used to join two shafts which are

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The maximum velocity of the driven shaft of a Hooke’s joint is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The angle between the axes of two shafts connected by Hooke’s joint is 18°. Determine the angle turned through by the driving shaft when the velocity ratio is maximum.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following mechanism is used to enlarge or reduce the size of a drawing ?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a pantograph, all the pairs are

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The Ackerman steering gear mechanism is preferred to the Davis steering gear mechanism, because

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following mechanism is made up of turning pairs ?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The speed of driving shaft of a Hooke’s Joint of angle 19.5^0 is 500 r.p.m. The maximum speed of the driven shaft is nearly

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a cone pulley, if the sum of radii of the pulleys on the driving and driven shafts is constant, then

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following statements is not correct? (a)Hooke’s joint is used to connect two rotating co-planar, non-intersecting shafts

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In case of a multiple disc clutch, if n1 are the number of discs on the driving shaft and n2 are the number of the discs on the driven shaft, then the number of pairs of contact surfaces will be

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The two links OA and OB are connected by a pin joint at O. If the link OA turns with angular velocity ω1 rad/s in the clockwise direction and the link OB turns with angular velocity ω2 rad/s in the anti-clockwise direction, then the rubbing velocity at the pin joint O is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Too much toe-in will be noticed by

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Caster action on the front wheels of a vehicle will

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

There are six gears A, B, C, D, E, F in a compound train. The numbers of teeth in the gears are 20, 60, 30, 80, 25 and 75 respectively. The ratio of the angular speeds of the driven (F) to the driver (A) of the drive is

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If the velocity ratio for an open belt drive is 8 and the speed of driving pulley is 800 r.p.m, then considering an elastic creep of 2% the speed of the driven pulley is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If the ratio of angular velocities of the driven and driving torque is one, find the Braking torque

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When two non-intersecting and non-coplaner shafts are connected by gears,the arrangement is known as helical gearing.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

...