If the ratio of angular velocities of the driven and driving torque is one, find the Braking torque

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Braking torque acts on which of the following member?

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Load torque is directly proportional to the input angular velocity.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

To split the engine torque in two ways, which of the following device is used?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Fixing torque’s value is independent of the load torque.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Resisting torque acts on which of the following member?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Input torque acts on which of the following member?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The ratio of speeds between gears is dependent upon the _________

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If the input power is increased to two times, what will be the effect of it on the fixed member power?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

There are six gears A, B, C, D, E, F in a compound train. The numbers of teeth in the gears are 20, 60, 30, 80, 25 and 75 respectively. The ratio of the angular speeds of the driven (F) to the driver (A) of the drive is

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

On a straight road motion, what is the purpose served by differential?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following is true regarding a differential?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following device allows the wheels of a car to rotate at two different speeds?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two wheelers are also equipped with a differential.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Maximum sliding velocity is the sum of angular velocities and its product with the length of path of contact.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts with an included angle of 160° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Find the maximum angular acceleration of the driven shaft.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

An electric motor drives a machine through a speed reducing gear of ratio 9:1. The motor armature, with its shaft and gear wheel, has moment of inertia 0.6 kg-m^2. The rotating part of the driven machine has moment of inertia 45 kg-m^2. The driven machine has resisting torque of 100 N-m and the efficiency of reduction gear is 95%. Find the power which the motor must develop to drive the machine at a uniform speed of 160 r.p.m.

asked Sep 23, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A speed reducer unit consists of a double-threaded worm of pitch = 11 mm and a worm wheel of pitch diameter = 84 mm. The ratio of the output torque to the input to rque is

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If the velocity ratio for an open belt drive is 8 and the speed of driving pulley is 800 r.p.m, then considering an elastic creep of 2% the speed of the driven pulley is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts having an included angle of 150° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Using the above data, calculate the maximum angular acceleration of the driven shaft in rad/s^2.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts having an included angle of 150° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Using the above data, calculate the maximum torque required in N-m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the maximum speed of the intermediate shaft if the driving shaft has a constant speed of 500 r.p.m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the maximum speed of the driven shaft if the driving shaft has a constant speed of 500 r.p.m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the minimum speed of the driven shaft if the driving shaft has a constant speed of 500 r.p.m.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A double universal joint is used to connect two shafts in the same plane. The intermediate shaft is inclined at an angle of 20° to the driving shaft as well as the driven shaft. Find the minimum speed of the intermediate shaft if the driving shaft has a constant speed of 500 r.p.m.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a simple gear train, if the number of idler gears is odd, then the direction of motion of driven gear will

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

...