The relation between linear velocity and angular velocity of a cycle

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The linear velocity of a point B on a link rotating at an angular velocity ω relative to another point A on the same link is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The linear velocity of a rotating body is given by the relation

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The linear acceleration of a rotating body is given by the relation

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The angular velocity of a rotating body is expressed in terms of

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The linear velocity of a point relative to another point on the same link is ……….. to the line joining the points.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The velocity of piston in a reciprocating pump mechanism depends upon

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

According to Kennedy’s theorem the instantaneous centres of three bodies having relative motion lie on a

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The instantaneous centre is a point which is always fixed.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a rotary engine the angular velocity of the cylinder center line is 25 rad/sec and the relative velocity of a point on the cylinder center line w.r.t. cylinder is 10 m/sec. Corioli’s acceleration will be

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

For the same crank length and uniform angular velocity of the crank in an offset slider crank mechanism, if the connecting rod length is increased by 1.5 times, the velocity of piston will

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a slider-crank mechanism, the crank is rotating with an angular velocity of 20 rad/s in counterclockwise direction. At the instant when the crank is perpendicular to the direction of the piston movement, velocity of the piston is 2 m/s. Radius of the crank is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a single link robotic arm the end-effector slides upward along the link with a velocity of 0.5 m/s while the link rotates about revolute joint with an angular speed of 1 rad/sec. When the end-effector is at a distance of 1 m from the joint, the acceleration experienced by the end-effector will be

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The magnitude of the Corioli’s component of acceleration of a slider moving at velocity V on a link rotating at angular speed ω is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Velocity of a point B in a link can be calculated by using the relation

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

There are two points P and Q on a planar rigid body. The relative velocity between the two points

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a slider crank mechanism, the crank rotates with a constant angular velocity of 300 rpm, Length of crank is 150mm, and the length of the connecting rod is 600mm. Determine linear velocity of the midpoint of the connecting rod in m/s. Crank angle = 45° from IDC.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a crank and slotted lever type quick return mechanism, the link moves with an angular velocity of 20 rad/s, while the slider moves with the linear velocity of 1.5 m/s. The magnitude and direction of Coriolis component of acceleration with respect to angular velocity are

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a lifting machine, the effort required to lift loads of 200N and 300N were 50N and 60N respectively. If the velocity ratio of the machine is 20 determine efficiency to load of 300 N.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a lifting machine, the effort required to lift loads of 200N and 300N were 50N and 60N respectively. If the velocity ratio of the machine is 20 determine maximum efficiency which can be expected from this machine.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a lifting machine, the effort required to lift loads of 200N and 300N were 50N and 60N respectively. If the velocity ratio of the machine is 20 determine efficiency to load of 200 N.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a lifting machine, the effort required to lift loads of 200N and 300N were 50N and 60N respectively. If the velocity ratio of the machine is 20 determine effort loss in friction at 200 N.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The velocity of a slider with reference to a fixed point about which a bar is rotating and slider sliding on the bar will be

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a lifting machine, the effort required to lift loads of 200N and 300N were 50N and 60N respectively. If the velocity ratio of the machine is 20 determine law of the machine.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The direction of velocity is parallel if the rotation is anticlockwise and perpendicular to the line joining links if the rotation is clockwise.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

What is the direction of velocity of a point in a link relative to another point on the same link rotating in a specific direction.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

...