4 strokes engine have a lower thermal efficiency than 2 stroke engine.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

4-stroke engine has one power stroke per 2 revolutions hence turning moment diagram is uniform.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following process is not the part of working of a 4 stroke I.C Engine?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Work produced by the 4-stroke engine is less because _______

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Compression stroke results in ________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A negative loop is formed in the turning moment diagram because the pressure inside the cylinder is _______ than the atmospheric pressure.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a 4 stroke IC engine, the angle θ assumes a value equal to _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a 4 stroke IC engine, Tmean = 1875 N-m, then find the work done per cycle.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the work is by on the gases, which of the following effect is observed on the turning moment diagram?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given turning moment diagram, the process X is known as ______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the work is done on the gases, which of the following effect is observed on the turning moment diagram?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

While drawing the turning moment diagram, which of the forces in not taken into account?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a four stroke I.C. engine, the turning moment during the compression stroke is

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the turning moment diagram of a multicylinder engine, the work done during exhaust stroke is by ______

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a 4 cylinder engine, when the pressure inside the cylinders exceeds the atmospheric pressure then.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a 4 cylinder engine, if the minimum speed of the engine is half the maximum speed, then coefficient of fluctuation is _________

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When engine torque is more than mean resisting torque, then the flywheel _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When engine torque is less than mean resisting torque, then the flywheel _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a multicylinder engine, the moment of inertia of a flywheel is 6500 kg-m^2, from the turning moment diagram, it is found that fluctuation of energy is 56000 N-m, if mean speed is 120 rpm, then find maximum speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The flywheel of a steam engine has a mass moment of inertia of 2500 Kg-m^2. The starting torque of the steam engine is 1500 N-m and may be assumed constant, using this data find the angular acceleration of the flywheel in rad/s^2.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a certain engine having an average speed of 1200 rpm, a flywheel approximated as a solid disc, is required for keeping the fluctuation of speed within 2% about the average speed. The fluctuation of kinetic energy per cycle is found to be 2 kJ. What is the least possible mass of the flywheel if its diameter is not to exceed 1 m ?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the stroke punch is 100mm, find the radius of the crank in mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The relation between stroke punch s and radius of crank r is ______

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Consider a three cylinder engine, the resultant turning moment diagram is the _____ of three cylinders.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a multicylinder engine, the coefficient of fluctuation of speed would vary with _________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A flywheel is fitted to the crankshaft of an engine having W as the amount of indicated work per revolution and permissible limits of coefficient of fluctuation of energy and speed as CE and CS respectively. The kinetic energy of the flywheel is given by

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

...