Consider a three cylinder engine, the resultant turning moment diagram is the _____ of three cylinders.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

For a multicylinder engine, the moment of inertia of a flywheel is 6500 kg-m^2, from the turning moment diagram, it is found that fluctuation of energy is 56000 N-m, if mean speed is 120 rpm, then find maximum speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the turning moment diagram of a multicylinder engine, the work done during exhaust stroke is by ______

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a 4 cylinder engine, when the pressure inside the cylinders exceeds the atmospheric pressure then.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a 4 cylinder engine, if the minimum speed of the engine is half the maximum speed, then coefficient of fluctuation is _________

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The flywheel of a steam engine has a mass moment of inertia of 2500 Kg-m^2. The starting torque of the steam engine is 1500 N-m and may be assumed constant, using this data find the angular acceleration of the flywheel in rad/s^2.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A negative loop is formed in the turning moment diagram because the pressure inside the cylinder is _______ than the atmospheric pressure.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Multi cylinder engines are usually placed at an equal inclination to each other.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a multicylinder engine, the coefficient of fluctuation of speed would vary with _________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

4-stroke engine has one power stroke per 2 revolutions hence turning moment diagram is uniform.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

From the turning moment diagram shown below, the minimum speed will occur at point _____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

From the turning moment diagram shown below, the maximum speed will occur at point _____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a turning moment diagram, the variations of energy above and below the mean resisting torque line is called

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The moment of inertia of a flywheel is 6500 kg-m^2, from the turning moment diagram, it is found that fluctuation of energy is 56000 N-m, if mean speed is 120 rpm, then find maximum speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The moment of inertia of a flywheel is 6500 kg-m^2, from the turning moment diagram, it is found that fluctuation of energy is 56000 N-m, if mean speed is 120 rpm, find the minimum speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a four stroke I.C. engine, the turning moment during the compression stroke is

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the work is by on the gases, which of the following effect is observed on the turning moment diagram?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given turning moment diagram, the process X is known as ______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the work is done on the gases, which of the following effect is observed on the turning moment diagram?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Area of the turning moment diagram represents _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

While drawing the turning moment diagram, which of the forces in not taken into account?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Turning moment is maximum when the crank angle is 90 degrees.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A single cylinder oil engine works with a three rotor system, the shaft length is 2.5m and 70mm in diameter, the middle rotor is at a distance 1.5m from one end. Calculate the free torsional vibration frequency for a two node system in Hz if the mass moment of inertia of rotors in Kg-m^2 are: 0.15, 0.3 and 0.09. C=84 kN/mm^2

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A single cylinder oil engine works with a three rotor system, the shaft length is 2.5m and 70mm in diameter, the middle rotor is at a distance 1.5m from one end. Calculate the free torsional vibration frequency for a single node system in Hz if the mass moment of inertia of rotors in Kg-m^2 are: 0.15, 0.3 and 0.09. C=84 kN/mm^2

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the minimum speed of the engine is half the maximum speed, then coefficient of fluctuation is _____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A V-twin engine has the cylinder axes at 90 degrees and the connecting rods operate a common crank. The reciprocating mass per cylinder is 23 kg and the crank radius is 7.5 cm. The length of the connecting rod is 0.3 m. If the engine is rotating at the speed is 500 r.p.m. What is the value of maximum resultant secondary force in Newtons?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

...