For a 4 stroke IC engine, the angle θ assumes a value equal to _______

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

For a 4 stroke IC engine, Tmean = 1875 N-m, then find the work done per cycle.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Work done per cycle is calculated as _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the figure given below, the areas BbC, CcD represent _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Coefficient of fluctuation of energy is ratio of _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Work produced by the 4-stroke engine is less because _______

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A shaft fitted with a flywheel rotates at 250 r.p.m. and drives a machine, the torque fluctuated about 18750 N-m, find the power required to drive the machine.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

To calculate power generated, product of maximum torque and angular speed is taken.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

4 strokes engine have a lower thermal efficiency than 2 stroke engine.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following process is not the part of working of a 4 stroke I.C Engine?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

From the turning moment diagram shown below, the minimum speed will occur at point _____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

From the turning moment diagram shown below, the maximum speed will occur at point _____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The fluctuation of energy is the variation of energy above the line of minimum torque.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

4-stroke engine has one power stroke per 2 revolutions hence turning moment diagram is uniform.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a 4 cylinder engine, when the pressure inside the cylinders exceeds the atmospheric pressure then.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a 4 cylinder engine, if the minimum speed of the engine is half the maximum speed, then coefficient of fluctuation is _________

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The swaying couple is maximum or minimum when the angle of inclination of the crank to the line of stroke ( θ ) is equal to

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The tractive force is maximum or minimum when the angle of inclination of the crank to the line of stroke ( θ ) is equal to

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the primary direct crank of a reciprocating engine makes an angle θ with the line of stroke, then the secondary direct crank will make an angle of . . . . . with the line of stroke.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a four stroke I.C. engine, the turning moment during the compression stroke is

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the turning moment diagram of a multicylinder engine, the work done during exhaust stroke is by ______

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the length of the connecting rod is unknown then the value (θ2 –θ1)/2π is equal to ________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a certain engine having an average speed of 1200 rpm, a flywheel approximated as a solid disc, is required for keeping the fluctuation of speed within 2% about the average speed. The fluctuation of kinetic energy per cycle is found to be 2 kJ. What is the least possible mass of the flywheel if its diameter is not to exceed 1 m ?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When engine torque is more than mean resisting torque, then the flywheel _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When engine torque is less than mean resisting torque, then the flywheel _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a multicylinder engine, the moment of inertia of a flywheel is 6500 kg-m^2, from the turning moment diagram, it is found that fluctuation of energy is 56000 N-m, if mean speed is 120 rpm, then find maximum speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

...