If the tank is moving vertically, which of its component is subjected to maximum total pressure?

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

A rectangular tank is moving horizontally in the direction of its length with a constant acceleration of 4.5 m/s2.The length, width and depth of tank are 7 m, 3m, 2.5m respectively. If tank is open at the top then calculate the total force due to water acting on higher pressure end of the tank.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A rectangular tank is moving horizontally in the direction of its length with a constant acceleration of 4.8 m/s^2. The length of tank is 7 m and depth is 1.5 m. If tank is open at the top then calculate the maximum pressure intensity at the bottom.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A rectangular tank is moving horizontally in the direction of its length with a constant acceleration of 5.5 m/s^2. The length of tank is 5.5 m and depth is 2 m. If tank is open at the top then calculate the minimum pressure intensity at the bottom.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A rectangular tank is moving horizontally in the direction of its length with a constant acceleration of 3.6 m/s^2. If tank is open at the top then calculate the angle of water surface to the horizontal.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A tank containing water upto a depth of 750 mm is moving vertically downward with a constant acceleration of 3.45 m/s^2. Find the force exerted by fluid of specific gravity .85 on the side of tank,width of tank is 2m

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A tank containing water upto a depth of 500 mm is moving vertically upward with a constant acceleration of 2.45 m/s^2. Find the force exerted by fluid of specific gravity .65 on the side of tank,width of tank is 1m.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

The pressure intensity at the bottom remains same, even if the tank moves with constant horizontal acceleration.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

There will be development of shear stress due to the dynamic motion of tank or container.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A tank containing water upto a depth of 650 mm is stationary. Find the force exerted by fluid of specific gravity .55 on the side of tank,width of tank is 1.5m

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A square lamina (each side equal to 2m) is submerged vertically in water such that the upper edge of the lamina is at a depth of 0.5 m from the water surface. If the pressure on the surface is 12 bar, what will be the total water pressure (in kN) on the lamina?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A square lamina (each side equal to 2m) is submerged vertically in water such that the upper edge of the lamina is at a depth of 0.5 m from the free surface. What will be the total water pressure (in kN) on the lamina?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A square lamina (each side equal to 2m) with a central hole of diameter 1m is submerged vertically in water such that the upper edge of the lamina is at a depth of 0.5 m from the free surface. What will be the total water pressure (in kN) on the lamina?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A tank contains water upto a height of 0.5 m above the base. An immiscible liquid of specific gravity 0.75 is filled on the top of water upto 1.5 m height. Calculate total pressure on side of the tank.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

What will be the total pressure (in kN) on a vertical square lamina submerged in a tank of oil (S=0.9) as shown in the figure?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

For an inclined plane for which position, maximum total pressure acts on it.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A rectangular plan surface 5 m wide and 7 m deep lies in water in such a way that its plane makes an angle 60⁰ with the free surface of water. Determine the total pressure force when the upper edge is 3 m below the free surface.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A rectangular plate surface 3m wide and 5m deep lies in fluid of specific gravity .9 such that its plane makes an angle of 45⁰ with water surface, upper edge 3m below free water surface. Determine the total pressure.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A square lamina (each side equal to 2m) is submerged vertically in water such that the upper edge of the lamina is at a depth of 0.5 m from the free surface. What will be the depth (in m) of the centre of pressure?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

What is the variation of total pressure with depth for any submerged surface if we neglect variation in the density?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Determine the centre of pressure on an isosceles triangle plate of base 6m and altitude 6m when it is immersed vertically in an oil of specific gravity 0.75. The base of the plate coincides with the free surface of oil.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

In a vertically submerged plane surface, pressure at evbery point remains same

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A large tank is filled with three liquids of densities ρ, 2ρ and 3ρ up to heights of ^h ⁄ 6, ^h ⁄ 3 and ^h ⁄ 2 respectively. What will be the ratio of the instantaneous velocity of discharge through a small opening at the base of the tank in this case to that if the container is filled with the liquid of density ρ only? (assume that the diameter of the opening is negligible compared to the height of the liquid column)

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A container is lled with two liquids of densities ρ and 2ρ up to heights h and eh respectively. What will be the ratio of the total pressure on the lower face AB and on the upper face BC?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The highest and lowest vertices of a diagonal of a square lamina (each side equal to 4m) are 1 m and 3 m respectively as shown. What will be the depth (in m) of it’s centre of pressure?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The total pressure or pressure intensity is zero for any point on inclined surface in space.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

...