If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Calculate the diameter of pin from shear consideration with maximum shear stress allowed is 40NN/mm² and an axial tensile force of 50kN is acting on the rod.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Knuckle Joint can’t be used to connect two intersecting rods.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which of the following are important parts of knuckle joint?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If no re boring allowance is to be given, then thickness of cylinder wall is max pressure is 3.5N/mm², bore diameter=200mm and permissible tensile stress is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Also longer arm is of length 500mm. If permissible bearing pressure on pin is 10N/mm² and diameter of the 20mm, find the shear stress in the pin.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate width of the band if permissible tensile stress is 80N/mm². Force P=15kN and diameter of the rivet can be taken as 9mm. Given thickness=3mm

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the diameter of the rivets by crushing consideration if permissible compression stress in rivets is 120N/mm², thickness of plate 3mm and P=15kN.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa.

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm².

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Can the cotter joint be used to connect slide spindle and fork of valve mechanism?

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If distance between the bolts from the axis of tilting is 125mm and 25mm, then find the effective tensile force acting on the bolts lying at 125mm from tilting axis.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm²Find the maximum amount of shear stress to which the body is subjected.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm². Find the minimum normal stress.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. If modulus of elasticity is 207000N/mm², calculate the initial nip.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In cold riveting like hot riveting shank is subjected to majorly tensile stress.

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m.

asked Jan 21 in Machine Design by Chris (48.2k points)

0 votes

0 answers

If allowable shear stress in the shaft is 70N/mm² and torsional and bending moments are M=1185000N-mm and m=330000N-mm, find the diameter of the shaft.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm². The diameter of shaft and width of key can be taken as 40mm and 10mm respectively.

asked 5 days ago in Machine Design by Carter (86.7k points)

...