The force of friction does not depends upon the roughness of the surfaces.

Question

The force of friction does not depends upon the roughness of the surfaces.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The force of friction is _____________ of the area of contact, between the two surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A boy (30 kg) sitting on his horse whips it. The horse speeds up at an average acceleration of 2.0 m/s 2.If the boy does not slide back, what is the force of friction exerted by the horse on the boy ?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The magnitude of the limiting friction (F ) bears a constant ratio to the normal reaction (RN) between the two surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The ratio of magnitude of the kinetic friction to the normal reaction between the two surfaces is_____________ than that in case of limiting friction.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction depends upon the material of which the contact surfaces are made.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

For moderate speeds, the force of friction

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction always acts in a direction, ___________ to that in which the body tends to move.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A heavy box of mass 20 kg is pulled on a horizontal surface by applying a horizontal force. If the coefficient of kinetic friction between the box and the horizontal surface is 0.25, find the force of friction exerted by the horizontal surface on the box.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The magnitude of the force of friction is ____________ to the force, which tends the body to move.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A boy (30 kg) sitting on his horse whips it. The horse speeds up at an average acceleration of 2.0 m/s 2.If the boy slides back during the acceleration, what can be said about the coefficient of static friction between the horse and the boy.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A wooden block is kept on a polished wooden plank and the inclination of the plank is gradually increased. It is found that the block starts slipping when the plank makes an angle of 18° with the horizontal. However, once started the block can continue with uniform speed if the inclination is reduced to 15°. Find the coefficient of static friction between the block and the plank.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A body of mass 400 g slides on a rough horizontal surface. If the frictional force is 3.0 N, find the magnitude of the contact force.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A body of mass 400 g slides on a rough horizontal surface. If the frictional force is 3.0 N, find the angle made by the contact force on the body with the vertical.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction is independent of the roughness of the surface.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction is inversely proportional to the normal load between the surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction is dependent of the substances of the bearing surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If the area of contact between the two surfaces is increased by two times, what will be the effect of it on the force of friction?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A multiple disc clutch has five plates having four pairs of active friction surfaces. If the intensity of pressure is not to exceed 0.127 N/mm^2, find the power transmitted at 500 r.p.m. The outer and inner radii of friction surfaces are 125 mm and 75 mm respectively. Assume uniform wear and take coefficient of friction = 0.3.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following statements regarding laws governing the friction between dry surfaces are correct?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

______________ is the friction experienced between two dry and unlubricated surfaces in contact.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The material used for lining of friction surfaces of a clutch should have _____________ coefficient of friction.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

______________ is the friction, experienced between the rubbing surfaces, when the surfaces have a very thin layer of lubricant.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

_____________ is the friction, experienced between the rubbing surfaces, when the surfaces have a thick layer of the lubricant.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The maximum efficiency of square threaded power depends upon

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A body of mass 1 kg is kept on a rough surface is being pulled by a force of 2N, what will be the value of coefficient of friction if it just begins to move. Take g = 10m/s^2.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-20T21:33:09+0000

Correct choice is (b) False

The explanation: The force of friction depends upon the roughness of the surfaces.

The force of friction does not depends upon the roughness of the surfaces.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories