The material used for lining of friction surfaces of a clutch should have _____________ coefficient of friction.

Question

The material used for lining of friction surfaces of a clutch should have _____________ coefficient of friction.

1 Answer

Related questions

+1 vote

1 answer

In case of a multiple disc clutch, if n1 are the number of discs on the driving shaft and n2 are the number of the discs on the driven shaft, then the number of pairs of contact surfaces will be

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The axial force (We) required for engaging a cone clutch is given by

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The torque developed by a disc clutch is given by

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a centrifugal clutch, the force with which the shoe presses against the driven member is the ___________ of the centrifugal force and the spring force.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A jaw clutch is essentially a

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A multiple disc clutch has five plates having four pairs of active friction surfaces. If the intensity of pressure is not to exceed 0.127 N/mm^2, find the power transmitted at 500 r.p.m. The outer and inner radii of friction surfaces are 125 mm and 75 mm respectively. Assume uniform wear and take coefficient of friction = 0.3.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The cone clutches have become obsolete because of

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

_____________ is the friction, experienced between the rubbing surfaces, when the surfaces have a thick layer of the lubricant.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A single plate clutch, with both sides effective, has outer and inner diameters 300 mm and 200 mm respectively. The maximum intensity of pressure at any point in the contact surface is not to exceed 0.1 N/mm^2. If the coefficient of friction is 0.3, determine the power transmitted by a clutch at a speed 2500 r.p.m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

______________ is the friction, experienced between the rubbing surfaces, when the surfaces have a very thin layer of lubricant.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction depends upon the material of which the contact surfaces are made.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction is _____________ of the area of contact, between the two surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The magnitude of the limiting friction (F ) bears a constant ratio to the normal reaction (RN) between the two surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Screws used for power transmission should have

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

For a body on an inclined plane, the value of coefficient of friction is equal to _____ (θ is the angle of friction)

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following statements regarding laws governing the friction between dry surfaces are correct?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

______________ is the friction experienced between two dry and unlubricated surfaces in contact.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction is inversely proportional to the normal load between the surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction does not depends upon the roughness of the surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction is dependent of the substances of the bearing surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If the area of contact between the two surfaces is increased by two times, what will be the effect of it on the force of friction?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The ratio of magnitude of the kinetic friction to the normal reaction between the two surfaces is_____________ than that in case of limiting friction.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A screw jack has square threads and the lead angle of the thread is α. The screw jack will be self locking when the coefficient of friction (μ) is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A heavy block of mass m is slowly placed on a conveyer belt moving with speed v. If coefficient of friction between block and the belt is μ, the block will slide on the belt through distance

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A boy (30 kg) sitting on his horse whips it. The horse speeds up at an average acceleration of 2.0 m/s 2.If the boy slides back during the acceleration, what can be said about the coefficient of static friction between the horse and the boy.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-21T02:45:15+0000

The correct answer is (b) high

To explain I would say: The material should have a high and uniform coefficient of friction.

The material used for lining of friction surfaces of a clutch should have _____________ coefficient of friction.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories