Klien’s construction can be used to determine acceleration of various parts when the crank is at

Question

Klien’s construction can be used to determine acceleration of various parts when the crank is at

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Klien’s construction can be used when

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The magnitude of the Corioli’s component of acceleration of a slider moving at velocity V on a link rotating at angular speed ω is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a rotary engine the angular velocity of the cylinder center line is 25 rad/sec and the relative velocity of a point on the cylinder center line w.r.t. cylinder is 10 m/sec. Corioli’s acceleration will be

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The magnitude of tangential acceleration is equal to

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Klein’s construction gives a graphical construction for

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The number of dead centers in a crank driven slider crank mechanism are

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Tangential acceleration direction is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The direction of Corioli’s component of acceleration is the direction

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a shaper mechanism, the Corioli’s component of acceleration will

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The velocity of a slider with reference to a fixed point about which a bar is rotating and slider sliding on the bar will be

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The sense of Coriol’s component is such that it

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Corioli’s component is encountered in

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Corioli’s component acts

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Klein’s constructions can be used to determine the acceleration of various parts at all locations.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a single link robotic arm the end-effector slides upward along the link with a velocity of 0.5 m/s while the link rotates about revolute joint with an angular speed of 1 rad/sec. When the end-effector is at a distance of 1 m from the joint, the acceleration experienced by the end-effector will be

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a slider-crank mechanism, the crank is rotating with an angular velocity of 20 rad/s in counterclockwise direction. At the instant when the crank is perpendicular to the direction of the piston movement, velocity of the piston is 2 m/s. Radius of the crank is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A body in motion will be subjected to coriolis acceleration when that body is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a lifting machine, the effort required to lift loads of 200N and 300N were 50N and 60N respectively. If the velocity ratio of the machine is 20 determine maximum efficiency which can be expected from this machine.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A slider sliding at 10 cm/s on a link which is rotating at 60 r.p.m. is subjected to Coriolis acceleration of magnitude

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a lifting machine, the effort required to lift loads of 200N and 300N were 50N and 60N respectively. If the velocity ratio of the machine is 20 determine effort loss in friction at 200 N.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The lengths of the links of a 4- bar linkage with revolute pairs only are p,q,r and s units. Given that p < q < r < s and s+p < q+r which of these links should be the fixed one, for obtaining a ‘double crank’ mechanism?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The lengths of the links of a 4-bar linkage with revolute pairs are p,q,r, and s units. given that p<q<r<s. Which of these links should be the fixed one, for obtaining a “double crank” mechanism ?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Bennett’ construction is used to determine graphically the velocity and acceleration of reciprocating parts of an IC engine.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Ritterhaus’ construction is used to determine graphically the velocity and acceleration of reciprocating parts of an IC engine.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a lifting machine, the effort required to lift loads of 200N and 300N were 50N and 60N respectively. If the velocity ratio of the machine is 20 determine efficiency to load of 300 N.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-19T02:18:16+0000

Right answer is (d) all of the mentioned

Explanation: Klien’s construction can be used to determine acceleration in all the mentioned position.

Klien’s construction can be used to determine acceleration of various parts when the crank is at

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories