Klein’s constructions can be used to determine the acceleration of various parts at all locations.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

In which of the following cases Klein’s construction can be used?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Klein’s construction gives a graphical construction of a 4 bar chain.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the acceleration of the piston is 0, then the velocity is _____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Bennett’ construction is used to determine graphically the velocity and acceleration of reciprocating parts of an IC engine.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Ritterhaus’ construction is used to determine graphically the velocity and acceleration of reciprocating parts of an IC engine.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

With respect to the figure given quadrilateral CQNO is known as _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In given figure, Triangle OCM is known as ________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If OC is the crank and PC is the connecting rod of a reciprocating steam engine and rotates with uniform angular velocity in clockwise direction in the given figure below: then under which condition the piston will undergo retardation?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Piston will remain in equilibrium if ________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given figure, the velocity of piston is maximum under which of the following conditions?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a slider crank mechanism, the total no. of dead centres are _____

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following construction methods is not used to calculate the velocity and acceleration of reciprocating parts of the internal combustion engine?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Klien’s construction can be used to determine acceleration of various parts when the crank is at

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin, if the angular acceleration of the rod is 23 000 rad/s^2, then find the correction couple in N-m.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The crank-pin circle radius of a horizontal engine is 300 mm. The mass of the reciprocating parts is 250 kg. When the crank has travelled 30° from T.D.C., the difference between the driving and the back pressures is 0.45 N/mm^2. The connecting rod length between centres is 1.2 m and the cylinder bore is 0.5 m. If the engine runs at 250 r.p.m. and if the effect of piston rod diameter is neglected, calculate the net load on piston.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin. What will be the new radius of gyration?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a horizontal engine, the weight of the reciprocating parts also add/subtract to the piston effort.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The crank and connecting rod of a steam engine are 0.3 m and 1.5 m in length. The crank rotates at 150 r.p.m. clockwise, determine velocity of the piston when the crank is at an angle 40 degrees from IDC.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the crank and the connecting rod are 300 mm and 1 m long respectively and the crank rotates at a constant speed of 250 r.p.m., determine the crank angle at which the maximum velocity occurs is ____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the crank and the connecting rod are 600 mm and 2 m long respectively and the crank rotates at a constant speed of 250 r.p.m, determine maximum velocity of the piston in m/s is _____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In which of the following cases Ritterhaus’ construction can be used?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In which of the following cases Bennett’s construction can be used?

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

From figure, acceleration of P with respect to C is given by_________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a horizontal engine, reciprocating parts are accelerated when the piston moves from _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a horizontal engine, reciprocating parts are retarded when the piston moves from _________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

...