Calculate the work done per minute by a punch tool making 20 working strokes per min when a 30 mm diametre hole is punched in 5 mm thick plate with ultimate shear strength og 450 Mpa in each stroke.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

In a punching press, the requirement is to punch 40 mm diameter holes in a plate having a thickness of 15 mm. The rate at which the holes should be punched is 30 holes/min. Energy requirement is of 6 N-m per mm2 of sheared area. If the punching takes time 1/10 of a second and the speed of the flywheel varies from 160 to 140 rpm, determine the mass of the flywheel having radius of gyration of 1 m.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

It is required to lift water at the top of a high building at the rate of 50 litres/min. Assuming the losses due to friction equivalent to 5 m and those due to leakage equal to 5 m head of water, efficiency of pump 90%, decide the kilowatt capacity of motor required to drive the pump.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In latitude 25.0 S, SA (spin axis) of a FG (free gyro) is in position S40E and horizontal. Find the tilt after 6 hours.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The steering of a ship means

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A machine punching 38 mm holes in 32 mm thick plate requires 7 N-m of energy per sq. mm of sheared area, find the maximum shear force required.

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+2 votes

1 answer

A flange mounted shear pin is used on a shaft as a safety device. The steel shear pin has a diameter of 2.38 mm and is to be mounted on the flange of shaft rotating at 650 rpm. The maximum power transmitted by the shaft is 4.5 KW. If the shear strength of material of pin is 30 MPa, the radial distance of its mounting is ____

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A ship propelled by a turbine rotor which has a mass of 5 tonnes and a speed of 2100 r.p.m. The rotor has a radius of gyration of 0.5 m and rotates in a clockwise direction when viewed from the stern. Find the gyroscopic effect when the ship sails at a speed of 30 km/h and steers to the left in a curve having 60 m radius.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A centrifugal Watt governor is fitted with two balls, each of mass 2.5 kg. Find the sped of the governor, when the balls rise by 20 mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A centrifugal Watt governor is fitted with two balls, each of mass 2.5 kg. Find the sped of the governor, when the balls fall by 20 mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A uniform disc of diameter 300 mm and of mass 5 kg is mounted on one end of an arm of length 600 mm. The other end of the arm is free to rotate in a universal bearing. If the disc rotates about the arm with a speed of 300 r.p.m. clockwise, looking from the front, with what speed will it precess about the vertical axis?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Pickering governor is driving a gramophone. Each disc attached to the centre of a leaf spring has a mass of 20 g. The width of each spring is 5 mm and thickness of 0.125 mm. The effective length of each spring is 40 mm. The distance from the spindle axis to the centre of gravity of the mass when the governor is at rest, is 10 mm, find the speed of the turntable in rpm if ratio of the governor speed to the turntable speed is 10.5.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Pickering governor is driving a gramophone. Each disc attached to the centre of a leaf spring has a mass of 20 g. The width of each spring is 5 mm and thickness of 0.125 mm. The effective length of each spring is 40 mm. The distance from the spindle axis to the centre of gravity of the mass when the governor is at rest, is 10 mm. Find the speed of the governor in rpm when the sleeve has risen to a height of 0.8 mm. (E = 210kN/mm^2)

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The mass of the turbine rotor of a ship is 20 tonnes and has a radius of gyration of 0.60 m. Its speed is 2000 r.p.m. The ship pitches 6° above and 6° below the horizontal position. A complete oscillation takes 30 seconds and the motion is simple harmonic. Determine Maximum gyroscopic couple.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The mass of the turbine rotor of a ship is 20 tonnes and has a radius of gyration of 0.60 m. Its speed is 2000 r.p.m. The ship pitches 6° above and 6° below the horizontal position. A complete oscillation takes 30 seconds and the motion is simple harmonic. Determine Maximum angular acceleration of the ship during pitching.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A power screw is rotated at constant angular speed of 1.5 revolutions/sec by applying a steady torque of 1.5Nm. How much work is done per revolution? What is the power required?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The heavy turbine rotor of a sea vessel rotates at 1500 r.p.m. clockwise looking from the stern, its mass being 750 kg. The vessel pitches with an angular velocity of 1 rad/s. Determine the gyroscopic couple transmitted to the hull when bow is rising, if the radius of gyration for the rotor is 250 mm.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a 4 stroke IC engine, Tmean = 1875 N-m, then find the work done per cycle.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the turning moment diagram of a multicylinder engine, the work done during exhaust stroke is by ______

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A connecting rod of mass 5.5 kg is placed on a horizontal platform whose mass is 1.5 kg. It is suspended by three equal wires, each 1.25 m long, from a rigid support. The wires are equally spaced round the circumference of a circle of 125 mm radius. When the c.g. of the connecting rod coincides with the axis of the circle, the platform makes 10 angular oscillations in 30 seconds. Determine the mass moment of inertia about an axis through its c.g.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A disc spinning on its axis at 20 rad/s will undergo precession when a torque 100 N-m is applied about an axis normal to it at an angular speed, if mass moment of inertia of the disc is the 1 kg-m^2

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the stroke punch is 100mm, find the radius of the crank in mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+2 votes

1 answer

A single plate clutch with both sides effective, has an outer diameter of 30 cm and inner diameter of 20 cm. the maximum intensity of pressure at any point in the contact surface is not exceed 1 kg/cm^2. If the co-efficient of friction is 0.3, determine the horse power transmitted by a clutch speed of 2000 rev/min.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying at 200 km per hr. The rotary engine and the propeller of the plane has a mass of 400 kg and a radius of gyration of 0.3 m. The engine rotates at 2400 r.p.m. clockwise when viewed from the rear. Find the gyroscopic couple on the aircraft.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a shaping operation, the average cutting speed is ( Stroke length S, Number of strokes per minute N, Quick return ratio R)

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A 10 teeth sprocket is operating at 200 rpm and driving a 25 teeth sprocket through a chain. The pitch of the chain is 20 mm and ultimate strength is 20 KN. Calculate the average linear speed.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

...